Ideas for DIY Line Array With Active Crossover!

[megasat16]

Don't know where to start but it's been in my mind for so long to build Open Baffle Type Line Array. I've already bought a few tweeters but it seems I need to buy more.

Here is what I already bought
2 pairs of Aurum Cantus G3si (6 ohms, 99db)
1 Pair of LCY 110 (8ohms, 92db)

I will only be using either G3si or LCY110 in the line array.

Both type of ribbons drives have fairly Frequency Response from 2KHz and above. I am thinking to use 8 to 16 in each line array. I am only testing at this stage and there is no solid design ideas yet. How many more tweeters should I get?

I am not sure what to get for the midrange but I've decided to go with Dual or Quad 15" Direct Servo Subs from Rythmik Audio.

I need suggestion for the suitable drivers for midrange array and the number of tweeters I should use. But most importantly, I need advise on Active XO for the tweeter and midrange arrays.

Thanks in advance for sharing your experiences!

[GV#27]

Cool project.I haven't done a line array or OB ,but Ive built a number of active xovers so I might be able to assist you with that part.

[megasat16]

Thanks GV! I've been doing a lot of readings on DIYA and AVS for line array and OB type speakers. What active XO did you use?

[GV#27]

What active XO did you use?I recently built this one.However I see the board is no longer available from Linkwitz. http://www.polkaudio.com/forums/showthread.php?t=79522&highlight=linkwitz+mt1+active+crossover

I bought one of these http://bryston.com/BrystonSite05/pdfs/PowerPacAmplifiers/driven.pdf

Aswell I built one with boards purchased from a group buy on DIYA.It also is no longer available but I will dig up the design manual for you as it's full of excellent info.

Another good source is Marchand,they have a number of PCB kits.http://www.marchandelec.com/

[GV#27]

I've decided to go with Dual or Quad 15" Direct Servo Subs from Rythmik Audio.

I missed this part on first read.Are you sure you want tight and detailed bass? :D Because thats exactly what you will get with the Rythmic servo's! Great choice IMO.;)

[megasat16]

I missed this part on first read.Are you sure you want tight and detailed bass? :D Because thats exactly what you will get with the Rythmic servo's! Great choice IMO.;)

Yes Sir! Tight and Deep is what I am after. :D It's got to be a long tower if I decided to use Quad. Can you picture the bass column from IRS Beta V? ;)

OMG, I'll be so broke after I am done buying all the drivers. :eek::eek:

[megasat16]

I recently built this one.However I see the board is no longer available from Linkwitz. http://www.polkaudio.com/forums/showthread.php?t=79522&highlight=linkwitz+mt1+active+crossover

I bought one of these http://bryston.com/BrystonSite05/pdfs/PowerPacAmplifiers/driven.pdf

Aswell I built one with boards purchased from a group buy on DIYA.It also is no longer available but I will dig up the design manual for you as it's full of excellent info.

Another good source is Marchand,they have a number of PCB kits.http://www.marchandelec.com/

Yeah! I thought about Marchand. The price of their fully assembled kits is high so I am thinking more of DEQX instead. I know KK-PCB offers active XO pcbs. Is that something you familiar with before?

http://www.kk-pcb.com/3-way.html

[GV#27]

Can you picture the bass column from IRS Beta V? ;)Oh ya,and when you move into a bigger house you can add another Quad column to match.:D


OMG, I'll be so broke after I am done buying all the drivers. :eek::eek:No s**t.
But atleast you have enough amplification laying around so as to not need to buy any.


I am thinking more of DEQX instead.Thats a very nice and sophisticated piece of audio engineering.Expensive but worth it.
I know KK-PCB offers active XO pcbs. Is that something you familiar with before?

http://www.kk-pcb.com/3-way.htmlNo I'm not familiar with it, but I took a quick look.I much prefer even order slopes (mostly LR4) but that board uses 18 db and I notice that one of the opamp pin spacings on the PCB is for a 14pin quad.There are not many hi performance opamps available in the quad package and the recommended TL074 is not IMO a good IC for hi rez audio.

[megasat16]

Oh ya,and when you move into a bigger house you can add another Quad column to match.:D



I don't know. I might have to sell 2 of my beloved SVS PB13 Ultra to make room. I can't afford a bigger house now. :D



No s**t.
But atleast you have enough amplification laying around so as to not need to buy any.



It's true. May be this super efficient tower will change my mind and I'll sell all my amps and settles on a few 7w SET amps. ::eek:



Thats a very nice and sophisticated piece of audio engineering.Expensive but worth it.



Yep! I think it's worth the price too when it is effectively 3 way active XO for both channels and has room correction. I saw the older 2.6 version for around 2K on Agon.



No I'm not familiar with it, but I took a quick look.I much prefer even order slopes (mostly LR4) but that board uses 18 db and I notice that one of the opamp pin spacings on the PCB is for a 14pin quad.There are not many hi performance opamps available in the quad package and the recommended TL074 is not IMO a good IC for hi rez audio.

Ok! Thanks for this one. I am in the new water when it comes to the high quality op-amps. :)

[Face]

Very cool project!

[GV#27]

I'll sell all my amps and settles on a few 7w SET amps. ::eek:That would be permissable if it were a few of these. http://www.passdiy.com/pdf/zenamp.pdf and not one with those glowing bottle thingies like this http://www.usatubeaudio.com/omaha-300b.php

[megasat16]

Very cool project!

Thanks Mike! I am still splitting hairs whether to get Accuton Midrange or Seas W22EX001. I'll be so broke to use 8 of the Accuton Midrange for each column.

From what I've read, I think Seas W22EX001 is an excellent candidate for very low distortion in OB type speakers (according to Linkwitz Labs).



That would be permissable if it were a few of these. http://www.passdiy.com/pdf/zenamp.pdf and not one with those glowing bottle thingies like this http://www.usatubeaudio.com/omaha-300b.php

Hehe...I will probably be using DIY Pass Labs Amps (may be more Levinson).

Speaking of amps, I have yet to work on the stuff I bought from Jim's Audio. I've just finished overhauling my Denon POA-3000 as I was hit with the Fake Tosh 2SA1095 and got to redo the output stages 3 times. :eek: This amp has one of the deepest bass slam ever.

Have you decided on your Pass Labs Project yet? :cool:

[Face]

That would be permissable if it were a few of these. http://www.passdiy.com/pdf/zenamp.pdf and not one with those glowing bottle thingies like this http://www.usatubeaudio.com/omaha-300b.phpIf you go with glowing thingies, it should be something more Manley. :D


Thanks Mike! I am still splitting hairs whether to get Accuton Midrange or Seas W22EX001. I'll be so broke to use 8 of the Accuton Midrange for each column.

From what I've read, I think Seas W22EX001 is an excellent candidate for very low distortion in OB type speakers (according to Linkwitz Labs). Since you're going active, I would lean towards the SEAS drivers. You don't see many OB designs using Accuton drivers, and since you're going active, it's easy to avoid the SEAS's breakup up top.

[megasat16]

If you go with glowing thingies, it should be something more Manley. :D

Since you're going active, I would lean towards the SEAS drivers. You don't see many OB designs using Accuton drivers, and since you're going active, it's easy to avoid the SEAS's breakup up top.

Manly sounds good to me. May be I can use stingrays and I really like how you powering the LSi15s.

I am waiting for PE or Madisound to discount on SEAS 10". It seems like a good idea to use SEAS too since it's been tested and proven in the Orion++ setup.

SEAS 10" can go down to 20Hz to 3000Hz and may be the answer for the midrange between Rythmik Subs and Aurum Ribbons.

But I have another crazy idea. Is 4 way Line Array idea too much?

I am not going to build everything overnight but I'll be collecting pieces and pieces at time and will be doing it as budget permits. I am guessing it'll probably take 1 year or so to be completed.

[Face]

Manly sounds good to me. May be I can use stingrays and I really like how you powering the LSi15s.

I am waiting for PE or Madisound to discount on SEAS 10". It seems like a good idea to use SEAS too since it's been tested and proven in the Orion++ setup.

SEAS 10" can go down to 20Hz to 3000Hz and may be the answer for the midrange between Rythmik Subs and Aurum Ribbons.

But I have another crazy idea. Is 4 way Line Array idea too much?

I am not going to build everything overnight but I'll be collecting pieces and pieces at time and will be doing it as budget permits. I am guessing it'll probably take 1 year or so to be completed.
The Stingray is an integrated amp, but the later units have a passive output/sub out. j

Which 10's are you talking about? Their Magnesium alloy (http://www.madisound.com/catalog/product_info.php?products_id=786) 10's are very impressive. They dig deep, have very low distortion, and are very articulate. Even in a ported enclosure they sound very tight. But just for sub duty, I would check out the new SEAS L26ROY (http://www.madisound.com/catalog/product_info.php?cPath=45_338_340&products_id=8535). Besides being much cheaper, they are even more impressive down low and don't require a large cabinet. I'd love to pick up a pair of them for sealed stereo subs.

Personally, I would only go with a 3 way, especially for a noob. :D;)

A pair or quad of L26's for the bottom, open baffle W22EX001 mids, and your silly ribbons on top. ;)

[megasat16]

10" SEAS model I have in mind is the bigger brother of the W22EX001 which Orion++ used. These W26EX001 goes down to 20Hz and can go up to 1000Hz (I got confused with another driver and said 3000Hz in the previous post which is incorrect). The very stiff cones in these SEAs driver seems excellent for the OB use.

Now, where is the noob who wants to design a 4 way? Let me kick him in the nuts. :D

What is L26s? I got to have line array or no array at all....:)

Edit : I found out what L26s mean...:D

[GV#27]

If you go with glowing thingies, it should be something more SheMan-leyfixed it.:D



I've just finished overhauling my Denon POA-3000 as I was hit with the Fake Tosh 2SA1095 and got to redo the output stages 3 times. :eek: Now that sucks donkey b**ls.


Have you decided on your Pass Labs Project yet? :cool:Im thinking F5 but need to find a good chassis.Also I should finish the numerous projects I've got on the go before diving into another.


tested and proven in the Orion++ setup. I want me a pair of them.




But I have another crazy idea. Is 4 way Line Array idea too much?I agree with Mike keep it a 3 way.


your silly ribbons on top. ;):eek:


10" SEAS model I have in mind is the bigger brother of the W22EX001 which Orion++ used. These W26EX001 goes down to 20Hz and can go up to 1000Hz (I got confused with another driver and said 3000Hz in the previous post which is incorrect). The very stiff cones in these SEAs driver seems excellent for the OB use.Another thing is linear excursion capability which is very important for OB useage.


Now, where is the noob who wants to design a 4 way? Let me kick him in the nuts. :DYep because that must be what he's thinking with wanting to go 4 way:eek::D.

[Face]

For OB subs, check out the servo subs on the bottom line here: http://www.gr-research.com/index.asp?PageAction=VIEWCATS&Category=11

The only thing I don't like about them is what appears to be a foam surround. In fact, I'll probably never buy another speaker with a foam surround due to their limited life span.

[Face]

fixed it.:DHey, you can ask any of the Polkies who were here, she single handedly kicked the crap out of a B1/F5 combo. :D


Another thing is linear excursion capability which is very important for OB usage. Check out the L26ROY's (http://www.madisound.com/catalog/product_info.php?manufacturers_id=183&products_id=8535) linear excursion, 28mm. :eek:

[GV#27]

she single handedly kicked the crap out of a B1/F5 combo. :DThats info I really did'nt need to know.:(


Check out the L26ROY's (http://www.madisound.com/catalog/product_info.php?manufacturers_id=183&products_id=8535) linear excursion, 28mm. :eek:That might work.

[Face]

Thats info I really did'nt need to know.:(
Since you're not a fan of tubes, you may have preferred the B1/F5 combo.








(probably not though)... :p
I believe it was due to the lack of baffle step and the Stingray's abundance of bass. Now that I've added some more baffle step, it might be a closer match.

[megasat16]

fixed it.:D



SheManley? A new tube pre from Manly? Named in the fashion of Pass Zen Series? Something like Bride of Zen?



I want me a pair of them.



Yep, Orion++ would be an excellent speaker for anyone. The Orion++ kit is on sale now. ;)



Im thinking F5 but need to find a good chassis.Also I should finish the numerous projects I've got on the go before diving into another.


Yeah...I find it hard to find a good DIY chassis too. May be, there are good sources in HongKong but shipping charges is high.



I agree with Mike keep it a 3 way.

Another thing is linear excursion capability which is very important for OB useage.

Yep because that must be what he's thinking with wanting to go 4 way:eek::D.

Can I call it 3 Way Plus Sub Arrays? It's hard to make 3 way and sounds awesome without a sub for OB. I've thought a lot about the driver choices and it's very limited what I can get. Cost is very high for very high quality drivers. And Even Orion+ has Thor SubWoofer to call it Orion++ :D

Yep...Xmax is very important too. For OB, low distortion, no cone breakup, high Xmax is needed but there are not many speakers around designed for this application. With the drivers I could afford, frequency response is very limited as a trade off for all these desirable qualities. That's why I am thinking to go 3 way plus subs (hehe...no official 4 way).

I think I still have another great choice - Lambda from Acoustics Elegance (AE Speakers). I need to talk with John from AE to find out what he can do for me. I know he can optimize customs drivers and I think Q of 0.7 for OB Bass Drivers would be very nice. ;) But the good Lambda drivers are not CHEAP either. :(

[megasat16]

For OB subs, check out the servo subs on the bottom line here: http://www.gr-research.com/index.asp?PageAction=VIEWCATS&Category=11

The only thing I don't like about them is what appears to be a foam surround. In fact, I'll probably never buy another speaker with a foam surround due to their limited life span.

Yep! I am not a fan of the foam surround either. The subs will not be OB. The servo sub array will be in sealed chambers.


Hey, you can ask any of the Polkies who were here, she single handedly kicked the crap out of a B1/F5 combo. :D

Check out the L26ROY's (http://www.madisound.com/catalog/product_info.php?manufacturers_id=183&products_id=8535) linear excursion, 28mm. :eek:

I don't recall seeing the thread about B1/F5 combo reviewed here. I wonder is that the DIY attempt at B1/F5 or the retail PassLabs Products?

28mm Linear Xmax is pretty impressive. But L26ROYs are 4ohms and they'll be power hungry. I am thinking High Efficiency Speakers so let me cheat by saying the whole speakers are designed to be very efficient but there are powered subs. :D

[CoolJazz]

Have you looked at doing bass with the Linkwitz Transform circuit?

Well executed, the LT setup does some of the most amazing bass! Super musical, deep tight notes! By well done I mean with excellent electronics and don't try to do it with a small box. Use a good driver and carefully follow Linkwitz info and it can be a big winner for music!

The down side is due to excursion it's only appropriate for music, not movie effects. And a vinyl guy would have to have a rumble filter and watch out for over excursion.

The LT can be stunning when well done!

CoolJazz

[Face]

I don't recall seeing the thread about B1/F5 combo reviewed here. I wonder is that the DIY attempt at B1/F5 or the retail PassLabs Products?
Both DIY. I still have the B1, it's being used in my bedroom rig.

[megasat16]

Have you looked at doing bass with the Linkwitz Transform circuit?

Well executed, the LT setup does some of the most amazing bass! Super musical, deep tight notes! By well done I mean with excellent electronics and don't try to do it with a small box. Use a good driver and carefully follow Linkwitz info and it can be a big winner for music!

The down side is due to excursion it's only appropriate for music, not movie effects. And a vinyl guy would have to have a rumble filter and watch out for over excursion.

The LT can be stunning when well done!

CoolJazz

Thanks CJ! I remembered reading about LT circuits but don't remember a thing about it so I had to dig it up from the net to refresh my memory. It's an excellent theory and circuit to make cheap drivers perform like a champ in a sealed enclosure. Even though I don't remember which manufactures offer it, I there there are some subwoofer plate amps available with built-in LT circuit in the XO.

It's a very nice way to tune the LF driver in the sealed enclosure with passive filters. If it's not for the Direct Servo Subs, I would surely use LT circuits in the LF drivers.

[megasat16]

Both DIY. I still have the B1, it's being used in my bedroom rig.

I know I probably shouldn't be saying this before wearing a flame suit and armored helmet.

But I think the DIY designs of Pass Series may not be as superior as the real B1/F5 combo?

I also think B1 may not be an ideal match to F5.

On the contrary, Stingray has ideally matched preamp driver circuits for it's Tube Amp so it should sounds good out of the box and it will sounds better than any mismatch combo. The only drawback is the limitation of power handling.

[Face]

That's possible, but the results weren't much different with a few different active preamps.

[megasat16]

It's very likely that a few different active preamp which probably does not match won't solve the problem either.

Anyway, I tried to make excuses even though it may not be the reasons why...:)

But What speakers were used in the test rig?

[Face]

Custom. ScanSpeak Air Circ (http://www.madisound.com/catalog/product_info.php?manufacturers_id=148&products_id=1738), SEAS Excel W12CY-001 (http://www.madisound.com/catalog/product_info.php?products_id=780), and SEAS Excel W26FX-001 (http://www.madisound.com/catalog/product_info.php?products_id=786).

Below 200hz is a little off due to the room.

http://face.cleanandquiet.com/store/5-21-09_Right.jpg

[megasat16]

Very Cool, Mike! I think I know this one. Very Nice FR graph. But why is there a dip around 50Hz-60Hz? XO correction, room acoustics? Is that FR from measured or simulated graph?

[Face]

That's my speaker's measured in room response. The dip is from the room...and that's after 6 GIK 244 panels and 2 GIK Monster Bass Traps.

[megasat16]

That's my speaker's measured in room response.


Yeah! That's why I said I know this one. Remember you sent me a link awhile ago? ;)



The dip is from the room...and that's after 6 GIK 244 panels and 2 GIK Monster Bass Traps.

:eek: That's serious bass void in that room. I recommend you call the Pro Terminators to cleanse the bass suckling creatures from that room if the treatments can't solve that dips.

[GV#27]

Since you're not a fan of tubes,Actually I do like tubes ,I just have a preference for SS.


Yep, Orion++ would be an excellent speaker for anyone. The Orion++ kit is on sale now. ;) Yes but still well outside my budget:(




Can I call it 3 Way Plus Sub Arrays? It's hard to make 3 way and sounds awesome without a sub for OB. I've thought a lot about the driver choices and it's very limited what I can get. Cost is very high for very high quality drivers. And Even Orion+ has Thor SubWoofer to call it Orion++ :DI guess technically I have what amounts to a 4way as I use subwoofers for the > 60hz range.




Thanks CJ! I remembered reading about LT circuits but don't remember a thing about it so I had to dig it up from the net to refresh my memory. It's an excellent theory and circuit to make cheap drivers perform like a champ in a sealed enclosure. Even though I don't remember which manufactures offer it, I there there are some subwoofer plate amps available with built-in LT circuit in the XO.I've used the LT in the past and it works great ,I'm now using somthing similar namely Rod Elliotts clone of Bag End's dual integrator circuit.Here is the gory details.http://sound.westhost.com/project48.htm


If it's not for the Direct Servo Subs, I would surely use LT circuits in the LF drivers.I believe Rythmic can supply an optional LT board for use with their plate amps.

[megasat16]

I guess technically I have what amounts to a 4way as I use subwoofers for the > 60hz range.

I've used the LT in the past and it works great ,I'm now using somthing similar namely Rod Elliotts clone of Bag End's dual integrator circuit.Here is the gory details.http://sound.westhost.com/project48.htm

I believe Rythmic can supply an optional LT board for use with their plate amps.

So, am I OK to use 3 way plus subs array now? ;) It's quite the same as 4 way.....:D

That's where I've seem the LT circuits offering in the sub plates before. :o

The servo sub plates do not have LT circuits since servo circuits does a similar thing - controlling the cone movement.

[GV#27]

So, am I OK to use 3 way plus subs array now? ;) Well I guess we can let you this time:p



The servo sub plates do not have LT circuits since servo circuits does a similar thing - controlling the cone movement.They can work together and infact will be complimentry but they serve different purposes.My understanding like yours,is that the servo's job is to keep the driver operating within it's linear range but does nothing to extend bass response.The LT on the otherhand will extend the response.The boost provided by the LT will require greater excursion demands of the driver but the servo will help to keep it in check.

[megasat16]

I guess you are right. I am reading it again but still not sure LT circuits are offered in the Servo Amps. I'll email Brian @ Rythmik. If I can get both features with Servo Subs, may be I'll be in Audio Nirvana! :)

On 2nd thought, may be not! The servo sub drivers may not be used with LT circuits. Oh heck, I'll email him now. :D



If you plan to build a sealed box and already bought the driver, we strongly recommend the Linkwitz Transform add-on board. Others may recommend using rumble filter or parametric EQ to extend the bass response. However, the bass extension obtained is never as as smooth as the one with Linkwitz transform circuit. For those who haven't bought the driver, we recommend the servo sub option.

[GV#27]

Yeah it appears from that you have a choice of one or the other not both.

[megasat16]

I got reply from Brian @ Rythmik about LT circuits. He said LT circuits is not required for the Direct Servo Subs.

I also decided to pull trigger on 12 more G3si ribbons while they are on sale. So, I can put 8 per tower.

I am thinking BG RD75 for midrange. But it'll give me only 92-94db sensitivity for the midrange section even if I put two of them in each tower. Using 4 in each array means a definite a 3rd mortgage on my home. :(

http://www.parts-express.com/pe/showdetl.cfm?Partnumber=264-700

RD75 can be crossed from 500Hz to 3KHz, and G3si can take it up from there.
W26-EX001 is good from 20Hz-500KHz and subs helping out the lower extension.

[Face]

And why do you need more than one of those per tower? :eek:

[megasat16]

RD75 is 88db average and it's only dipole line source (not array). In order to be array, I need at least 2 and it'll only give me additional 6db theoretical gain. It's still fall short of the high efficiency from the LF and HF driver arrays. We'll see what it can do if I put two together.

[megasat16]

This one looks promising too! I could afford to put 8 drivers per tower and crossed from 500Hz-3KHz. G3si can take up from there.

http://www.madisound.com/catalog/product_info.php?products_id=1314

[GV#27]

I got reply from Brian @ Rythmik about LT circuits. He said LT circuits is not required for the Direct Servo Subs.

Ah OK so he is doing more than just controling excursion with his servo.


This one looks promising too! I could afford to put 8 drivers per tower and crossed from 500Hz-3KHz. G3si can take up from there.

http://www.madisound.com/catalog/product_info.php?products_id=1314
Or get the poor man's version.http://wbx.me/l/?p=1&u=http%3A%2F%2Fmadisound.com%2Fmadisound_news%2F20 09%2F08%2Fzaph-audio-za14w08-5-midwoofer.html

Appears to be a great little driver for the money.

[megasat16]

Thanks GV! I think it's a very similar driver to the Seas with one important difference for me. I think the SEAS could be used for OB due to the dynahex magnet and motor structure is non-blocking for the rear resonances. I could still use Zaph and save a ton of money on the mids but I need to mount 8 more in the back (as in the G3si). G3si is also not dipole. It's rear chamber is completely sealed so I need to put 4 in front and 4 in rear. I could do the same with the Zaph driver. It's very likely I need to use T-Pads for rear drivers attenuation.

Check this out. I think this is a cute line array! :D Before building BIG, I probably should start off with the small one. :D

http://www.walyou.com/blog/2009/03/27/mini-array-computer-speakers/

[megasat16]

12 More G3si Ribbon Tweeters Have Arrived Last Week so I'll be biting sawdust soon. That makes 8 x G3si in each tower. Soon will be the moment of truth about how they sounds. :D

Midrange is still undecided. Bummer!

[GV#27]

Whats this?your pissing away money on tweets when you should be buying more vintage amps.:D

Nice!you have your treble end of the spectrum covered.

btw.be sure to wear your resporator mask if your cutting MDF.That stuff is just down right nasty on the lungs.

[ben62670]

BB opa4134

[megasat16]

BB opa4134

Why the OP Amp? :confused:

[ben62670]

A day late and a dollar short. Earlier in the thread there was discussion of doing an active 3 way XO.
http://www.kk-pcb.com/3-way.html
I just wanted to put this up as a good performing option at a very reasonable price.

[megasat16]

Whats this?your pissing away money on tweets when you should be buying more vintage amps.:D



That's the box 12 G3si are shipped in. :D I've pissed away enough money on the Vintage Amp for now and I am well satisfied with what I have. It's time to try on some Vintage Preamps.



Nice!you have your treble end of the spectrum covered.


Well, I hope it sounds good. I have yet to test anything.



btw.be sure to wear your resporator mask if your cutting MDF.That stuff is just down right nasty on the lungs.

Thanks for reminding! I'll wear all the safety gears and mask when I cut the MDF. That sawdust are nasty stuff for sure. I'll be using a router to recess the tweeters also.

[megasat16]

A day late and a dollar short. Earlier in the thread there was discussion of doing an active 3 way XO.
http://www.kk-pcb.com/3-way.html
I just wanted to put this up as a good performing option at a very reasonable price.

Ahh...I see. Thanks Ben! I thought about the 3 Way XO from KK-PCB also but my hands are itching to try the DEQX for active XO.

[ben62670]

The really nice thing about the pro XO is the ability to change nearly every parameter on the fly. It can also be used in future projects:)

[GV#27]

As previously mentioned the DEQX would be the cats meow if you can snag one.

Aswell I see from the pic you have your study materials on wood finishing and Dickasons excellent LDCB.You might recognize a name on pg32.:)

[megasat16]

As previously mentioned the DEQX would be the cats meow if you can snag one.

Aswell I see from the pic you have your study materials on wood finishing and Dickasons excellent LDCB.You might recognize a name on pg32.:)

The HT room with test rigs also doubles as a study room for me.

Dickasons wrote an excellent LDCB book and I am glad to have a copy. But I think mine is a different version from yours and I don't see any familiar name on PG.32. The version I have discusses about damping correlation to box sizes and Q of various types of XO networks.

[Face]

My book appears to be different also. I don't have it in front of me at the moment, but I believe it's version 7.

[megasat16]

I have 7th edition also. I also got a Free CD from the Old Colony Sound Lab.

[megasat16]

As of today, this project is standing still due to the fact I have lack of time and I couldn't find an appropriate (efficient) Mid Drivers for OB between 500Hz to 5KHz.

[Face]

That's a broad range for most drivers to play without any audible distortion or beaming. I would check out the Accuton C79, ScanSpeak 12MU/4731T, 12M/4631G, 10F/4424G, 10F/8424G, or SEAS W12CY-03. The last two ScanSpeak drivers I mentioned have excellent response to 6k, but I don't know how well they would do at 500hz in your application.

Here's someone else using them in a dipole, but only from 1-6k: http://techtalk.parts-express.com/showthread.php?t=218810

[megasat16]

Yo Mike! I hear you. :) You want to help me fund half of the cost for C79? :p I only need about 16 or 32 (your pick) of them for both sides. :D

Thanks for the link also! I will read it tonight.

[Face]

Sure, if you help me fund a pair of SS Be tweeters and C173-6-090 mids...and all CAST caps, inductors, and resistors to go with them. :D

[megasat16]

Cool! Let me raise the bars a bit, eh? I haven't told you about the woofers yet, right? :D

I am thinking 4 of Alain 15A for each sides only coz I think 28A would be too much for bass, you in? ;)

[megasat16]

Well, after about 2 years in waiting and pondering over the affordable and suitable drivers, I am taking a small towards the mids and the lows with 16 of these.

https://www.madisound.com/store/product_info.php?products_id=8863

Heard it has a hump around 10K for Full Range uses but I am crossing them with the tweeters array at 3K-3.5K, so I am all good. These has 9mm Xmax too and OB tested by other DIYers.

Mike, Thanks for confirmation about these drivers! :wink:

Qts is higher than I would like for OB woofer but I am using 2 columns of 4 sealed subs arrays so I don't think I need to worry about bass...

[20hz]

Well, after about 2 years in waiting and pondering over the affordable and suitable drivers, I am taking a small towards the mids and the lows with 16 of these.

[url]https://www.madisound.com/store/product_info.php?products_id=8863[/
Mike, Thanks for confirmation about these drivers! :wink:..

I heard good things on the audiance A3 driver , audiance has a website (lots of info) .

[megasat16]

Qts is higher than I would like for OB woofer but I am using 2 columns of 4 sealed subs arrays so I don't think I need to worry about bass...

Damn...I need to prove read after what I wrote. :redface:

What I meant Qts is actually lower than I would like for an OB woofer.



I heard good things on the audiance A3 driver , audiance has a website (lots of info) .

Thanks! I also heard a lot of nice things about Audiance A3 but these little drivers are quite expensive. I found them on clearance once on E-speaers.com but even then, these are quite expensive for a line array with 16 on each side. A3 is 3" and 82dB sensitivity so needs a lot of them.

So, it's decided on the Alpair 12 with 6.5" driver and 89dB sensitivity.

[20hz]

Thanks! I also heard a lot of nice things about Audiance A3 but these little drivers are quite expensive. I found them on clearance once on E-speaers.com but even then, these are quite expensive for a line array with 16 on each side. A3 is 3" and 82dB sensitivity so needs a lot of them.

So, it's decided on the Alpair 12 with 6.5" driver and 89dB sensitivity.

True I could never buy a A3 ( Price and a 3" ) what surprised me was A3 xmax its almost 1/2" .
Thay alpair looks pricey how much are they ?

[geoff727]

Megasat16,

I have watched this thread since it's inception, and am really looking forward to what you develop as I have a similar project in the works.

A couple of questions. About the Alpair driver, that is quite a substantial mounting flange on that driver. And, multiple drivers will be combined into your line array. Assuming a center-to-center driver spacing of about 6 inches if the mounting flanges are tucked up against one another, this will result in comb lines forming above about 2200Hz, and the first cancellation occuring above 4400Hz. I was curious if you were planning any mitigation techniques for the comb filtering, and, given the cancellation frequency, what frequency you were planning to bring the tweeters in at.

Also, can you describe your bass tower design (monopole, dipole, or bipole; type, frequency, and slope of crossover, etc.)? Did you finally opt for the Rythmik gear (that's what I'm planning on using)?

Very anxious to see your results.

G~

[geoff727]

Just read up in the posts and saw the tweeter xover freq.

G~

[megasat16]

True I could never buy a A3 ( Price and a 3" ) what surprised me was A3 xmax its almost 1/2" .
Thay alpair looks pricey how much are they ?

Yeah. A3 seems well made driver. I think the long throw design with very high Xmax for this little beast is all thanks to the XBL motor.

The other thing I think it's a bit confusing is about how the drivers companies quote the Xmax. The Xmas is usually peak (or one way) measurement but some do quotes Xmax(p-p). And for some reasons, the companies who market these drivers just use the Xmax word without the word (p-p) as they should. It's very frustrating so I usually check with the manufacturing or the store to confirm what it really means.

I found the Alpair 12 on specials at madisound. It's been going on for a while for sure and the ones with Gold cones are sold out. The single driver setup may looks neat with gold cone but for 8 of the gold cones mounted on each channel, I think it may looks a bit too much.

https://www.madisound.com/store/product_info.php?products_id=8864


Megasat16,

I have watched this thread since it's inception, and am really looking forward to what you develop as I have a similar project in the works.

A couple of questions. About the Alpair driver, that is quite a substantial mounting flange on that driver. And, multiple drivers will be combined into your line array. Assuming a center-to-center driver spacing of about 6 inches if the mounting flanges are tucked up against one another, this will result in comb lines forming above about 2200Hz, and the first cancellation occuring above 4400Hz. I was curious if you were planning any mitigation techniques for the comb filtering, and, given the cancellation frequency, what frequency you were planning to bring the tweeters in at.

Also, can you describe your bass tower design (monopole, dipole, or bipole; type, frequency, and slope of crossover, etc.)? Did you finally opt for the Rythmik gear (that's what I'm planning on using)?

Very anxious to see your results.

G~

Geoff,

Thanks for the interest! The summary below is my general design intent with regards to the Alpair 12 but it's nothing solid till proven.

The Alpair 12 has 8" frame with 6.5" cone so I am mounting the mid arrays on 3 stacks of 3/4" thick and 16" wide baffle. The vertical driver spacing (center to center) will be between 10" to 11" depending on how the driver performs. I will test a couple of Alpair 12 mounted in a test OB before the final cut and assembly. The 4" baffle on each sides of the Alpair 12 will have enough front to rear wave separation and enough lows to use with woofers array above 100Hz.

Every alternate drivers may be mounted from front to back (i.e. the front of the driver facing backwards) and wired out of phase so the acoustic power will be evenly distributed on the front and the back sides.

I am still debating much on the woofer choice but I've decided it will be a sealed array on each channel. I like to use Rythmik 15" drivers but it's undecided at this time.

I think I'll get the builds for the mids and tweeters arrays completed in a couple of months but the bass arrays will take some time. I'll post some pictures as things going forward.



Just read up in the posts and saw the tweeter xover freq.

G~

Yeah, tweeter xover is between 3KHz-3.5KHz.

[20hz]

whats always thrown me was XMAX & XMECH (what exactlly is the differance ?
That peak to peak is missleading but the effeciancy thing is very important , what is it 3db=twice the needed power ??
I heard the 4 ohm spl rating is actually differant than the 8 ohm rating wheras 83 db @4 ohms compares closely to 86 DB at 8 ohms , now I dont know the exact #'s like many folks on this site but that is just something I heard ..

[geoff727]

whats always thrown me was XMAX & XMECH (what exactlly is the differance ?

Usually, there are limits of excursion relating to linearity of output, and there are limits of excursion relating to the sheer physical structure of the thing. Xmax is voice coil length minus air gap height, then divide that by two. That's your typical linearity Xmax. As far as the physical structure, moving backwards it will at some point strike the coil former against the back plate. Moving forward, there's also just so far it can go. But, these are outside the limits of output linearity.




That peak to peak is missleading but the effeciancy thing is very important , what is it 3db=twice the needed power ??

Correct, a 3dB difference in sensitivity erquires twice (or half) the amplifier output for the same SPL.

G~

[geoff727]

Mega...,

I hope it's okay if I do some thinking here, about your intriguing project!


The Alpair 12 has 8" frame with 6.5" cone so I am mounting the mid arrays on 3 stacks of 3/4" thick and 16" wide baffle.

With the 3 stacks of drivers, are you going with a 9-driver array then? I thought I read a while back that you were going with 8. Actually, 9 is a good figure to use. With 3 paralleled groups of 3 drivers wired in series, there's an impedance load presented to the amplifier that's the same as the amplifier would see if it were driving one single driver. This is assuming equal drive along the array- no power tapering.




The vertical driver spacing (center to center) will be between 10" to 11" depending on how the driver performs. I will test a couple of Alpair 12 mounted in a test OB before the final cut and assembly. The 4" baffle on each sides of the Alpair 12 will have enough front to rear wave separation and enough lows to use with woofers array above 100Hz.

11" corresponds to a wavelength 1232Hz. With a center-to-center (ctc) driver spacing of 11", comb lines will begin forming along the array at this frequency. At twice this frequency, 2464Hz, cancellation will occur, yielding a lobing response when measured up and down the array. This is still well below the proposed mid-tweet xover frequency; in this region, significant comb lines will be present.

This suggests to me that, if that driver spacing is to be used, the maximum mid-tweet xover frequency used should be no higher than 1200 Hz (this is obviously fairly low and would require some robustness in the tweeters). Still, this does not take into account the system power response, but it is something to think about if a constant wavefront is to be presented from the speaker (the goal of a line array).

I was a bit concerned about the driver spacing and baffle width, so I ran a simulation in a simple baffle simulator software that does not take into account the response of the drivers themselves, only the projected response of the (flat) baffle coupled with the locations and shape of the drivers. I used the following parameters: Baffle width of .4 m (about 16 in), baffle height of 2.1 m, drivers spaced evenly along the array with a ctc distance of .25 m (9.8 in, which is a bit under what you listed above, but was easy to graph). With these dimensions, there is an >8dB dipole peak at 500 Hz, followed by a rapidly downward-sloping response to the first significant notch (-6dB) at 1800 Hz. The rest of the response shows deep notch combing above this frequency, extending outside of the -7dB lower limit of the graph.

What the actual musical consequences of this baffle response will be in a real-life line array is beyond my level of current knowledge. I think if it were me, I would still consider four things:

1. Reducing the ctc spacing as much as possible to reduce the comb line formation and adjusting the mid-tweet crossover frequency as necessary. And/Or,

2. Experimenting with off-center mounting of the Alpair midranges on the baffle, running some simulations, and measuring. And/Or,

3. Consider power-tapering the outer drivers in the array so they recieve slightly less signal. Or,

4. Consider going with a lom-m-t-m-lom configuration (lom = lower output, power-tapered midrange). So, you'd end up with a speaker kind of like the Audio Artistry Beethoven Grand, one of Linkwitz's designs.





Every alternate drivers may be mounted from front to back (i.e. the front of the driver facing backwards) and wired out of phase so the acoustic power will be evenly distributed on the front and the back sides.

If i'm understanding correctly, then I have a couple of initial thoughts.

1. The response for the rear-facing drivers will be different than for the front-facing ones, due to the sound being emanated by an inverted cone, and working it's way around the magnet structure. This could alter response in odd ways. Measurement is in order.

2. I think I understand your thought about even acoustic power radiation (like an omnidirectional speaker [mbl's]) to preserve the same spectral signature of sounds that are re-radiated from room reflections, thus reducing coloration of the system. I have a couple thoughts here. First, driver directivity in the upper frequency registers will naturally reduce this, as will dipole behavior in the lower registers. Also, it may be worth considering if even power response is an acheivable or desirable goal here, given that the front and rear sides of the dipole are radiating into different acoustic spaces (like one being 4' away fom a wall, the other side into a great big 19'-long room, for example.). I need to keep reading up on this.




I am still debating much on the woofer choice but I've decided it will be a sealed array on each channel. I like to use Rythmik 15" drivers but it's undecided at this time.

Going back to the response of the Alpair driver itself, as you noted, it has a Qts of .327. Perhaps we could consider an "ideal" open-baffle Qts as .7 or so. With a Qts of .327, the natural roll-off of the driver will begin at, perhaps, a frequency of Fs x 3. This is reflected in the roughly 12 dB/octave rolloff curve posted on madisound for the driver.

I use a pair of Rythmik 12" drivers on my system right now, the aluminum-coned ones. They recommend not to cross them any higher than about 80 Hz. Going higher, they recommend using the GR Research paper-coned drivers (yes, with those unfortunate foam surrounds!). I imagine this recommendation probably holds true for the 15" drivers as well. I have not actually listened to the 12" drivers at anything above about 50 Hz, so I don't know how musical they are above that 80 Hz recommendation.

So, I will assume for the moment a mid-woof crossover of 100Hz (with whatever woofer). Looking back at the simulated predicted baffle response, the 500 Hz dipole peak slopes down to a 0dB-line crossing point at about 75 Hz. At 100 Hz, there is still a 2dB rise. Looking at the frequency response graph at madisound, the response of the Alpair driver at 100Hz is down about 6dB from the published 89dB sensitivity.

Have you considered building some test baffles out of cardboard of different sizes and geometries, and testing each one for the best response (both on and off axis)?




I think I'll get the builds for the mids and tweeters arrays completed in a couple of months but the bass arrays will take some time. I'll post some pictures as things going forward.

I can't wait to see it!

Thanks for letting me expound a bit (and please excuse me for being long-winded!). What you come up with is going to be a learning experience for me as well, and I hope we can have some good forum conversations on your design. It has certainly got me thinking, and very interested. I'm staying tuned....

Geoff

[geoff727]

I think if it were me, I would still consider four things:

One more just came to mind:

Build the array with a concave front baffle, so that each driver is equidistant from the listening position (similar to the Gryphon Poseidon loudspeaker).

G~

[megasat16]

Hello Geoff,

I've been a bit busy lately so I couldn't post in length yet. However, I've read your thoughts and I appreciate and welcome your inputs.

I'll reply to your posts over the weekend. Please feel free to post any other thoughts and ideas meanwhile.

Thanks,
James

[megasat16]

Oh..I forgot to say I may have to go with different drivers than Alpair 12. Madisound don't have enough of Alpair 12 I ordered. So, Alpair 10 V2 seems a possible substitute and I can use 12 on each column.

http://www.markaudio.com/pdf/d5.pdf

[megasat16]

Mega...,

I hope it's okay if I do some thinking here, about your intriguing project!



The ideas are always welcome and appreciated, Geoff! Good ideas are worth a fortune.




With the 3 stacks of drivers, are you going with a 9-driver array then? I thought I read a while back that you were going with 8. Actually, 9 is a good figure to use. With 3 paralleled groups of 3 drivers wired in series, there's an impedance load presented to the amplifier that's the same as the amplifier would see if it were driving one single driver. This is assuming equal drive along the array- no power tapering.



I think I said something confusing about 3 stacks of .75" Birch Ply. I meant triple stacks of cut and routed MDF glued together for the baffle thickness to dampen the vibrations.

But since you mentioned 9 drivers, it's true that it represents an 8 ohms impedance for wiring a group of 3 drivers in series and then all 3 groups in parallel. I don't know how it would meaure up for efficiency of the entire 9 drivers.

I don't know how it'll compare efficiency for wiring four groups of (2 speakers in series) which will give me an impedance a bit lower than 4 ohms.

It's up for testing and measuring after I've figured out the optimal driver spacing.



11" corresponds to a wavelength 1232Hz. With a center-to-center (ctc) driver spacing of 11", comb lines will begin forming along the array at this frequency. At twice this frequency, 2464Hz, cancellation will occur, yielding a lobing response when measured up and down the array. This is still well below the proposed mid-tweet xover frequency; in this region, significant comb lines will be present.

This suggests to me that, if that driver spacing is to be used, the maximum mid-tweet xover frequency used should be no higher than 1200 Hz (this is obviously fairly low and would require some robustness in the tweeters). Still, this does not take into account the system power response, but it is something to think about if a constant wavefront is to be presented from the speaker (the goal of a line array).



I wonder where I can get the formula to calculate the comb line. It would be great if I can use that formula to do some calculations when I am doing the testing.

This is a different formula I found a while back.

http://www.mh-audio.nl/calcmaxfreq.asp

I am going to cut a lot of plywoods and test mount the drivers and do both extensive listening test as well as the measurements.

I think the problem with line arrays and lobing is that you'll need to listen from a distance. The closer you sit to the speakers, the more the lobing is apparent even for using the small size drivers and mount them very closely together. But I hope the OB with diffused acoustical patterns will reduce the lobing somewhat than the regular boxed speakers.




I was a bit concerned about the driver spacing and baffle width, so I ran a simulation in a simple baffle simulator software that does not take into account the response of the drivers themselves, only the projected response of the (flat) baffle coupled with the locations and shape of the drivers. I used the following parameters: Baffle width of .4 m (about 16 in), baffle height of 2.1m, drivers spaced evenly along the array with a ctc distance of .25 m (9.8 in, which is a bit under what you listed above, but was easy to graph). With these dimensions, there is an >8dB dipole peak at 500 Hz, followed by a rapidly downward-sloping response to the first significant notch (-6dB) at 1800Hz. The rest of the response shows deep notch combing above this frequency, extending outside of the -7dB lower limit of the graph.



One other thing I wonder is what software lets you to simulate the FR of the Line Array?

I got some Alp 12 drivers landed yesterday. I need to wait a certain time to get the rest of the drivers in but I have 8 now to try out. But looking at the drivers, the frame around the cone is quite large (about 1.5") so mounting them closely (8.25" ctc) would be a good start for a trial cut and mount. I think given the driver size of approximately 8", I am sure there will be a certain peaks and dibs in FR if comb filters are not applied. I was thinking to use DEQX for the speaker control and measurements but looks like I need to wait a while to get one. That's why a lot of people using the smaller drivers in a line array but I opt out for the lower efficiency and awful looks. I think even using smaller drivers, lobing is very apparent when you sit close to the speakers.




What the actual musical consequences of this baffle response will be in a real-life line array is beyond my level of current knowledge. I think if it were me, I would still consider four things:

1. Reducing the ctc spacing as much as possible to reduce the comb line formation and adjusting the mid-tweet crossover frequency as necessary. And/Or,

2. Experimenting with off-center mounting of the Alpair midranges on the baffle, running some simulations, and measuring. And/Or,

3. Consider power-tapering the outer drivers in the array so they recieve slightly less signal. Or,

4. Consider going with a lom-m-t-m-lom configuration (lom = lower output, power-tapered midrange). So, you'd end up with a speaker kind of like the Audio Artistry Beethoven Grand, one of Linkwitz's designs.



Thanks Geoff! I am well considering your advise. Everything including baffle types is also up for the experimentation since I wanted to get it right.




If i'm understanding correctly, then I have a couple of initial thoughts.

1. The response for the rear-facing drivers will be different than for the front-facing ones, due to the sound being emanated by an inverted cone, and working it's way around the magnet structure. This could alter response in odd ways. Measurement is in order.

2. I think I understand your thought about even acoustic power radiation (like an omnidirectional speaker [mbl's]) to preserve the same spectral signature of sounds that are re-radiated from room reflections, thus reducing coloration of the system. I have a couple thoughts here. First, driver directivity in the upper frequency registers will naturally reduce this, as will dipole behavior in the lower registers. Also, it may be worth considering if even power response is an acheivable or desirable goal here, given that the front and rear sides of the dipole are radiating into different acoustic spaces (like one being 4' away from a wall, the other side into a great big 19'-long room, for example.). I need to keep reading up on this.



You read my thoughts exactly on this.

I don't know how it'll work out but there are people who has done this with OB speakers but not with the Line Arrays. I think the SPL is uneven for a cone type driver since the rear chamber has mostly everything that disturbs the sound wave to travel freely to the rear side. But having said that, I think the MA driver has quite open frame type in the rear and plenty of room for the rear waves radiation. I agree measurement and experimentation is in order.

One most important thing above all is to achieve less lobing, less cancellation and better FR graph while maintaining the added efficiency. May be it's everything I wanted but not sure can be obtainable. :biggrin:




Going back to the response of the Alpair driver itself, as you noted, it has a Qts of .327. Perhaps we could consider an "ideal" open-baffle Qts as .7 or so. With a Qts of .327, the natural roll-off of the driver will begin at, perhaps, a frequency of Fs x 3. This is reflected in the roughly 12 dB/octave
rolloff curve posted on madisound for the driver.

I use a pair of Rythmik 12" drivers on my system right now, the aluminum-coned ones. They recommend not to cross them any higher than about 80 Hz. Going higher, they recommend using the GR Research paper-coned drivers (yes, with those unfortunate foam surrounds!). I imagine this recommendation probably holds true for the 15" drivers as well. I have not actually listened to the 12" drivers at anything above about 50 Hz, so I don't know how musical they are above that 80 Hz recommendation.

So, I will assume for the moment a mid-woof crossover of 100Hz (with whatever woofer). Looking back at the simulated predicted baffle response, the 500 Hz dipole peak slopes down to a 0dB-line crossing point at about 75 Hz. At 100 Hz, there is still a 2dB rise. Looking at the frequency response graph at madisound, the response of the Alpair driver at 100Hz is down about 6dB from the published 89dB sensitivity.



Yes, an ideal and critically damped OB woofer should have Qts closer to 0.7. With the Alpair 12, I think the woofer XO would be above 100Hz for the same reason you mentioned. That's why I am not sure of using subwoofers. Subwoofers generally will go lower for deeper bass but can't usually go high on the XO point.

It's one of many things I am not sure how to solve yet. I am looking at a lot of OB woofers and most people use very efficient Pro Audio woofers with their OB setup. But there is options such as lambda series woofers from AESpeakers.




Have you considered building some test baffles out of cardboard of different sizes and geometries, and testing each one for the best response (both on and off axis)?



I got many sheets of plywoods waiting to be cut for the test baffles. I am going to start cutting since I got my router setup again for the circle cutting yesterday. Everything is in order and I am about to get one step closer. :smile:




I can't wait to see it!



Thanks Geoff! It's going to take some time to get the speakers build right but when I am done, you are more than welcome to see it and hear it in person. :wink:

[megasat16]

Thanks for letting me expound a bit (and please excuse me for being long-winded!). What you come up with is going to be a learning experience for me as well, and I hope we can have some good forum conversations on your design. It has certainly got me thinking, and very interested. I'm staying tuned....

Geoff

Yes, I enjoy the discussion too. Please feel free to think some more and chime in. And stayed tuned as I post some results of the initial tests.

A few things I wanted to point out.

1. I need to wait for 8 more Alp 12 to arrive (in fact, it'll be on special order since Madisound doesn't has enough for me).

2. I may just as well go with smaller Alp 10 Gen 2 (alp10.2) series since Madisound got enough of them in stock. All depends on how I like the Alp12 in the initial test. But from the data, I think Alp10.2 seems a better choice for the OB line array.

3. If I go with the Alp10.2, I would have to return them to Madisound or just sell it on the DIY forum. I may also make a couple of MTM with Alpair 12 or a single point source OB.

4. Alpair Drivers takes quite a consideration to break in and Mark Audio has very specific info for breakin of their drivers. So, it'll take a couple of weeks for drivers breakin before I can take any kind of measurements.


One more just came to mind:

Build the array with a concave front baffle, so that each driver is equidistant from the listening position (similar to the Gryphon Poseidon loudspeaker).

G~

Nice speakers they are. Yeah, I could possibly try that too. Thanks for the suggestion.

James

[geoff727]

One other thing I wonder is what software lets you to simulate the FR of the Line Array?

James,
I'm going to write quite a bit more, as I have time (maybe a little bit each day). As each subject comes up, I'm trying to keep digging into the papers about theory and design (both line array and open baffle, for which the two concepts have to be combined), to attempt to keep everything i say as accurate as possible. As you know, these things are way too expensive to goof up. This is actually really good for me, in light of my upcoming design.

This is the baffle simulator i used, it's called "The Edge".

http://www.tolvan.com/

It simulates the response of the baffle ONLY, so the infinite baffle response of the drivers have to be mentally superimposed onto the baffle response to come up with the system response. The good thing about it is, it allows for multiple drivers on one baffle (i.e., a line array). It can be a diffraction simulator for closed-box speakers (very helpful with baffle step considerations), or can simulate responses of a rectangular open baffle. It?s free, so if you end up downloading it, I can send you the file that I generated (I saved it), and you can tweak it from there, if you want.

Here are a couple others I have used briefly, but only very briefly as they cannot simulate an array. However, they DO take driver parameters into account:

http://www.t-linespeakers.org/downloads.html (This one is called ?xlbaffle?)

http://www.musicanddesign.com/A_B_C_Dipole.html

Martin J. King also has his mathcad worksheets for $25. I THINK they will do pretty much everything that The Edge and xlbaffle will combined, but i'm not sure since I haven't used them (yet). http://www.quarter-wave.com/

The musicanddesign website also has a great open-baffle theory section. I have not used any of the 'payware' software that can model open baffles. I put the freeware version of LEAP V Enclosure Shop on the computer, but I haven't explored any of it yet. I know, though, that it will do some open baffle modeling. Whether it will do it in a line array, I don't know.

For my system, I have the configuration pretty well nailed down. And, I just have to prepare to build a whole bunch of test baffles and measure, measure, measure, and keep experimenting until I have the width, shape, backward curve, etc., all correct (maybe in 3 more years!). I have not as yet found any papers documenting theory of construction of open baffle line arrays. Everything is either open baffle OR line array. So, that means the experimentation time will be a little longer. But, that's okay. Not like anybody hasn't done it before!!


But since you mentioned 9 drivers, it's true that it represents an 8 ohms impedance for wiring a group of 3 drivers in series and then all 3 groups in parallel. I don't know how it would meaure up for efficiency of the entire 9 drivers.

I?m assuming a nominal 8-ohm impedance for the Alpair 10.2 here. For 8 drivers (4 paralleled sets of two wired in series, yielding an impedance of 4 ohms), I get a sensitivity of 99dB SPL. For 3 paralleled sets of 3 in series (9 drivers), yielding 8 ohms impedance, it comes up as 96.5 dB SPL. Pretty close, and pretty good.

Here?s a simple online calculator: http://members.optusnet.com.au/~gradds55/arraycalc.xls
It will probably work for your array (circular drivers), but not as well for mine (discrete planar elements), because the dispersion pattern of those drivers is different.



It's going to take some time to get the speakers build right but when I am done, you are more than welcome to see it and hear it in person.

I would LOVE to! I actually do make it a point to go see/hear other peoples' systems that are of high quality.

I am envious about those Aurum Cantus tweeters. I've heard them in the big Evolution Acoustics speakers (and probably others without noticing it), and they were great!

Geoff

[CoolJazz]

First the greatest info on a line array...Dr. Jim Griffin's paper. Here...

http://www.audioroundtable.com/misc/nflawp.pdf

Second...I wonder just how much to be concerned about comb filtering? For those not sure what it is, you can hear this effect on many TV newscast's when they have multiple mics open and the natural sounding voice goes to a slightly tin can effect. Listen as they go over to a single mic and the hollow effect goes away to a naturally mic'ed voice. What I'm wondering is how much does it come into play and does the number of drivers tend to increase this effect?

I've been playing with OB efforts for a couple of years. The lack of box coloration and the sound stage filling the whole end of the room is wonderful! My "issue" is to try and get the gain, the dynamics more like a horn. This has lead me to multiple drivers. So I've (being cheap) picked up some economical full range drivers from Parts Express. Using 3, 8" full range drivers, mounted on a 20" wide flat board, spaced a little too far apart. This done to allow later reuse of the lumber and to increase the comb filter effect to allow easier investigation. Well...to music you just can't seem to hear it!! In theory, I'd think the duo-cone construction would have the hf coming from at least 4" apart (??) and with about 2 inches between drivers on this, more than that! So where is it? Would it be greater if this was a full line?

Woofer duty is similar and works well. I have on a seperate column, 4 10" drivers, currently crossing at 180hz (as that's a xover handy). This cross puts only a single hq cap in the high pass and is active for the lp. The bass has all you could want and measured to roll off at around 30hz but keep in mind that's only a 6db roll there so energy will be going lower. Pretty cool seeing a total of 14 drivers looking at you and knowing it's still only around $300 looking at you!

But the sound quality has really floored some of my friends which are pretty picky! The 8" full rangers I tried dropping from 3 each side, to two and then to a single. Interestingly enough, a single sounds like a cheap driver but each one you add sounds better and better. Going to try, before moving on, to redo these closer together and add a fourth and see if it gives yet another step up in dynamics and quality.

BTW...the 8's have a qts of about 1, so did try them with no woofer support..hmmm...pretty interestingly good in bass. Need to try to add a little control to keep it from being to flabby, the First Watt F1 being a current source needs something added to control that low end just a little.

Guess I wanted to share the fun a little and encourage the effort and suggest that you can learn a bit without using too expensive of drivers to start out with! I'll be following along too!!

CJ

[megasat16]

James,
I'm going to write quite a bit more, as I have time (maybe a little bit each day).
Geoff

Thanks Geoff! Sounds good and appreciate for the links. I am busy cutting today. I'll post more reply later.


First the greatest info on a line array...Dr. Jim Griffin's paper. Here...

http://www.audioroundtable.com/misc/nflawp.pdf


Guess I wanted to share the fun a little and encourage the effort and suggest that you can learn a bit without using too expensive of drivers to start out with! I'll be following along too!!

CJ

Thanks Mark! It's nice to see you posting in this thread. I'll post more reply after taking time to read your link. Meanwhile, if you find more info, please keep posting.

James

[geoff727]

First the greatest info on a line array...Dr. Jim Griffin's paper. Here...

http://www.audioroundtable.com/misc/nflawp.pdf

Second...I wonder just how much to be concerned about comb filtering?

You know, this is interesting. Here is a picture of a speaker (the Reference 5 LS, I think, from Anthony Gallo), that on the surface, would seem to go against the ctc spacing guidelines set forth in Griffin's paper. Admittedly, I know next-to-nothing on the design of Gallo speakers. Do any of you guys have any insights on this one?

Griffin's paper is geared (and titled) towards near-field arrays. So there has to be some point (going into the far field) where the coalescence of the sound renders the comb line formation much less important or audible.

I do remember reading in different places that some people thought that the audibility of comb filtering was inconsequential. I wonder if they're listening from far enough away so that the sound is coalescing into a more coherent whole. It's an interesting point, seeing that comb filtering happens on a lot of the regular speakers we listen to every day also.

Any thoughts?

About far field listening.....one of the complaints that I've heard people make about line arrays is that they seem to make instruments/voices/images seem much larger than life, like a 10-foot-tall violin. Of the arrays I've listened to, this has never been so. In fact, one array I listened to a couple years ago (the Scaena 3.2's) had an extremely lifelike rendering of image size and depth, in the setup that I heard them in. I wonder if the unnatural image growth that some have complained about is a result of listening from too far away. Remembering back, almost all of the listening I've been able to do of line arrays has been in the near field.

What do you guys think?

For my current system, I listen with a ratio of 77% distance between the speakers as distance to the listening seat, and it's about 9 feet to the listening chair. Now these are line sources, not arrays, but I have never experienced from these speakers any unnatural growth in image size.

G~

[geoff727]

I think the problem with line arrays and lobing is that you'll need to listen from a distance. The closer you sit to the speakers, the more the lobing is apparent even for using the small size drivers and mount them very closely together. But I hope the OB with diffused acoustical patterns will reduce the lobing somewhat than the regular boxed speakers.

Now see, this is what happens when I just think and type as I go without remembering what I just read! I say what's already been said. :rolleyes:

[Face]

Another take on line arrays: http://www.audiocircle.com/index.php?topic=92134.60

[CoolJazz]

A couple of quick thoughts...

Thanks for throwing that forum discussion in Face! I'd happened to have just sat and read the Keele paper a few days ago and discussed some of it with some of the guys. To put the link over here...

http://www.xlrtechs.com/dbkeele.com/CBT.php

I would reinforce that what I was commenting on that I'm currently playing with is OB, a short line and full range drivers. My listening position is by measurement 11 ft from ear to full range driver center. I can raise up and down and not notice a change in response really at the listening position. Up real close the drivers finally seperate but I'd never listen real, real close anyway. Any multi-driver seperates up close too or course.

I'm sure the comb effect there and to really find it, I've been meaning to bring up white noise on a between stations postion on a FM rcvr or better yet use a test disc. But the point is, and question too I guess, how much of problem is it?

BTW...one of the 3 most commented on systems from Altanta Axpona was a line array. I believe it was the Scaena name you mentioned Geoff. Big line in a really, really big ballroom sized setup. Very impressive. I'd say a bit big of an image but not huge. But it's hard to just in that big of a room! Probably 30-40 ft behind them and we had to be seated 20ft from them. Very impressive for sure, just unrealistic for mere mortals pricing wise... Speaking of crazy price...the biggest image I ever remember hearing was the larger MBL's. Very open sounding...just couldn't get over the face singing to you sounding like it was Golly Green Giant sized!

Many years ago, I heard the Gallo in the single ball stage and then later a taller 3 way I think with the side firing woofer? Don't know a thing about a line though.

I did hear a build of Dr. Griffin's once about 7-8 years ago. Did set the gears to grinding...just took a few years I guess. :smile:

CJ

[CoolJazz]

Oh...and have you guys seen this one??

http://trueaudio.com/array/index.htm

[geoff727]

In post #80, I conjectured:


I wonder if the unnatural image growth that some have complained about is a result of listening from too far away.

In Griffin, page 20, paragraph 2, talking about the resons for power tapering, he says, "If listeners move away from the array, the image seems to bloom and grow in height."




BTW...one of the 3 most commented on systems from Altanta Axpona was a line array. I believe it was the Scaena name you mentioned Geoff. Big line in a really, really big ballroom sized setup. Very impressive. I'd say a bit big of an image but not huge. But it's hard to just in that big of a room! Probably 30-40 ft behind them and we had to be seated 20ft from them. Very impressive for sure, just unrealistic for mere mortals pricing wise...

I wonder when Scaena is going to come back to RMAF. That's the only show I've been making, and they haven't been for a couple years. You are right about the price. The array with 12 midranges is something like $45,000. The 18-driver array is twice that. I guess that's why guys like us have learn to build our own!:biggrin:

Do any of you guys go to RMAF? It would be fun to meet up for a beer.

Here's some pics of the Scaena's, designed by the same guys who did the Nearfield Acoustics Pipedreams.

G~

[geoff727]

It looks like those Don Keele CBT speakers are available at P.E. in kit form, here:
http://www.parts-express.com/cbt36/

I think this is the driver they use. Sure is getting lots of very positive feedback from people.

http://www.parts-express.com/pe/showdetl.cfm?Partnumber=290-212

Those speakers are just really interesting. Guess I better start reading up.

Here is another interesting system. This one was at RMAF a couple years ago. I think one of the people at Balanced Power Technology custom built it. Open baffle with an RD75 for the treble, and open baffle woofer line. Crossover, OB equalization, and notch filter for the RD75's cavity resonance was all handled by a DEQX.

[megasat16]

I finished cutting a plywood for 4 drivers test baffle (2 on each side). I am liking FRD (full range driver) coz it works without any bloody XO.

[megasat16]

Now see, this is what happens when I just think and type as I go without remembering what I just read! I say what's already been said. :rolleyes:

The more I read, the better it is. I always think reading or learning something repeatedly as making the ideas or topics sink into you. No harm in anyway. :wink:


Another take on line arrays: http://www.audiocircle.com/index.php?topic=92134.60

Thanks Mike! It's a curved array. Its sure helps for the lobing but I imagine the soundstage could be a bit stretched?