Search:

I think that the Smart Strips use current drawn through the main recepticle to trigger the switched outlets. I don't believe that I could make it work for my application, but thanks for the link!!
...

O.K.- you guys have made me re-think this whole deal. Although I can' t plug the four Scythe S-Flex 12v fans directly into the Denon's triggers because they draw 100MA each and the triggers total...

Thanks disneyjoe7,
I guess I need to clarify what I want to do. I have a Denon 4308 receiver that I use as a prepro with an EMO MPS-1 amp. I want to use the two 12v assignable triggers on the 4308...

Hi-
I need to find an inexpensive 12v switched 120v AC power strip to run some fans for my equipment. I searched and the only 3 that came up were the Monster(eeek!!) HTFS 500, the Panamax M8-HT Pro,...

I found "Recessed Low Voltage Cable Plates" at www.datacommelectronics.com, Phone #770-6628205. They have single,double, and tripple gang box wall plates with a "chute" cast into the rear to guide...

Henry- I don't know if you looked at the Owner's Manual pdf for the 4806CI on Denon's site- I printed this out, less the remote codes, when I was researching this model. There are a lot of features...

I run my Emotiva MPS-1 amp(300w/x7ch) and a Velodyne 1000w sub off a Panamax 4400 20amp power center with no problems. The Panamax power cord requires a 20 amp recepticle, which has the neutral prong...

Henry;

That sounds like a good deal, I think that the 4806CI lists for $4000. There is a large thread called "The Official Denon AVR-4806 Thread" at avsforum that has a great deal of information...

Hi Henry-
Denon will update all of their upper level receivers including the 4806CI this year(4808CI?) according to info released at CES. The updates include HDMI 1.3, onboard decoding for the new...

Post reported

Hi-
I ran my starter HT system with six RTi4's, a CSi3 center, and a PSW303 sub for about a year before upgrading. I would have used RTi6 speakers for the fronts if I had enough space. One of my...

Hi Jockos-
I asked Polk CS for the part number and price for the LSi15 8" woofer grille on June 29,06. They said that the 8" grille has part number RF0647-1 and costs $12.00 ea. You can order it by...

Hi marcd51,
If you're asking about the "SACD FILTER" setting of either 50Khz or 100Khz shown on page 42 of the Owner's Manual, these settings are used to allow high frequency cut off above those two...

I just finished wiring my new LSi speakers with custom Signal Cable bi-wires and I was very impressed with the quality and sound. Part of the fun in buying new gear is the satisfaction that you get...

Toxis, I thought the same thing. My CSi3 is flippable(new word?) and I have read about others using LSiC's vertically on stands as mains. I think that it probably makes no difference unless there are...

After nearly four decades of marriage and raising our daughters I think I'll keep her. I'm also very carefull not to get her too po'd- she was a service brat and the old gunny's taught her how to...

I just finished installing the new LSi15 fronts and LSiC center -they made a huge improvement over the RTi4 and CSi3 speakers that they replaced. I tried the center in the normal posistion and...

My monster Sony tv (350lbs w/stand) has to be placed in the corner so I'm stuck with setting the LSi15 fronts next to it. I had the RTi4 speakers on stands in the same location and they sounded...

Thanks for your reply Dennis, I flipped my LSi Center just to try it in that position and if it su**'s. I can always reverse it. Re the swap of the LSi15's, I have my TV and speakers in the corner of...

I'm in the process of installing my birthday present to myself, new LSi15 fronts in cherry and a LSiC center. I have to place the center on top of my 40" Sony XBR tv, which is 53 inches above the...

I received the LMC-1 this afternoon and had planned on taking my new toy out of the box tonight and start some preliminary configurations......play with it! I just checked back w/ their web site and...

I ordered the Emotiva LMC-1 back in January, and Brown has it in their truck for delivery today. YeeHaw! I don't know if they told you, but they will also ship you a free 2x1 HDMI switcher (mfd by...

David- I just checked Denon's site and all the codes are still listed in Owners>Product Support & Archives>Discontinued Products Archive. I printed the remote code pdf for a backup. The Memorex DVD...

MrNightly-
I have a Denon 3805 and the remote codes were on a seperate document from the manual. The 2 codes for Sony DVD players are 0560 and 0891. You can print these codes from Denon's website in...

I bought a set of the locking banana plugs last week for my Emotiva MPs-1 amp at the distributor, Orange County Speaker. They worked great, but as others have posted, I was concerned about the...