Search:

Very nice install...would you mind telling me where the factory amp is on that vehicle? Is it behind the kickpanel passenger side, or is it under the center console?

Not sure what the golden ratio is, but, if you look at my enclosure from the top down, there isn't one 90 degree angle. Looking at it from the side, there are only 2 90 degree angles, so I most...

I can't use any of the box examples, as I need/want to build a box to utilize the rear "corner" of my trunk so as to keep as much usable trunk space as possible. If I build a custom box, I can...

I'm going to build a sealed box, and thanks for the info as far as voice coils and ohms, that's what I needed to know. If the dimensions of the box should not be even, what if I went with a 12" face...

I'm planning on adding one of these to the trunk of my 07 Altima and powering it off of a Sony XM-1S amp (290w @4 ohms, 500w @2 ohms). Would it be best to run this sub with both voice coils in...

Not yet...Unfortunately I tore my lateral meniscus in my left knee while finishing up the install, and I just had surgery 2 days ago. I've got a buddy who is pretty good at setting up systems, but I...

Should I turn on the HPF on the amp? What setting should I begin with/what is the lowest range the MMC6500's can handle efficiently without distortion?

I am using the factory H/U (non-bose), into a Navone LOC with the voltage adjustments of the LOC set to MAX (9.5v, I believe). I used the LOC instead of the line level inputs as I was under the...

Bass boost is off, bass and treble controls on H/U are set to "0", gain controls on amp are at lowest setting (full counter-clockwise), and the HPF/LPF switch on the amp is turned off (full signal to...

I just finished my install in my 07 Altima. I put MMC6500's in the front door with the tweeters flush-mounted in the top of the door panel. I put MMC690's in the rear deck. I have them powered...

Ascalon,
I know I'm reviving an old thread, but I was wondering if you ever got this worked out? I just finished an install with a set of MMC6500's in the front doors, and MMC690's in the rear deck...

I don't live in Hawaii (don't I wish :o), I live in Cleveland, Ohio. I'm a police officer (Hawaii 5 Oh', the old police show), so I guess I'm dating myself now :eek:! I prefer to do the installs...

Thanks! There are a few car audio shops near me, but they have some pretty shady people working there, so I tend to stay away.

Thanks, that's what I wanted to know. I will run a LOC from the stock H/U and RCA's to the amp. Then I will run the SW 14g to the front and rear crossovers, and the MOMO wires from the crossovers...

I figured the wire supplied with the MOMO's would be decent enough just to run from the crossovers to the speakers. I can never find connectors in 14g to connect 14g wire to the speakers, so I...

OK guys, I'm going to put the crossovers in the doors, now how bout the wiring? I wanted to use the included wire on the "speaker" end, as they have the nice connectors on them. I would then splice...

I've got 50' of wire, should be more than enough. I need to know if I can splice the 14g wire that I bought to the factory wiring that came with the speakers. The wiring that came with the speakers...

Thanks MacLeod,
What are your thoughts on splicing 14 gauge wire to the smaller gauge wire that came with the speakers?

I'm working on getting my components installed in my 07 Altima. I have the woofer in the door in the stock location, and the tweeter is flush mounted high in the panel, just forward of the interior...

Great advice guys, (and/or girls :)) and thanks, that's just what I needed to know. I'd get a second 4 channel and run each individually, but my wife is going to kill me as it is :p.

Forgot to mention that I have a Navone l.o.c. to run patch cables from my head unit to my amp. Here's a stupid question. My amp is a 120 x 4 channel amp, since both sets of speakers utilize a...

I have a set of MMC6500's for the front doors, and a set of MMC690's for the rear deck of my 07 Altima, and was wondering the best way to wire them? My amp is a Kicker ZX650.4 120w x 4 amp. Should...

Great!!! Thanks!!!

As far as amps, I'm looking at one of these two:
Alpine MRP-F550 90W X 4 @ 4ohms
JBL Grand Touring Series GTO75.4 II 104W X 4 @ 4ohms

Thanks for the response MacLeod. If I run both L+R components off of only two channels (running the crossover in single mode), I'm guessing that the crossover will split the power to each speaker...