Free Shipping on All Orders 1-866-764-1801

Vist our Online Store

Search:

Type: Posts; User: Mark_1042

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    785

    The Adcom is great, doesn't even break a sweat...

    The Adcom is great, doesn't even break a sweat when driving the A7's. I can't really compare it to the sound of the receiver as I've never ran them off of the receiver. This is all a new set up,...
  2. Replies
    16
    Views
    785

    Just to note, I also checked the speaker levels -...

    Just to note, I also checked the speaker levels - I had tried adjusting them manually but the calibration did a better job then I could, so I just went with the ones it set up. The levels look...
  3. Replies
    16
    Views
    785

    Per the user manual setting the center to "none"...

    Per the user manual setting the center to "none" redirects the center channel signal to the fronts. I'll double check the manual but I'm pretty sure that's the way it works.

    On a good note, I...
  4. Replies
    16
    Views
    785

    Tried repositioning speakers and ran the...

    Tried repositioning speakers and ran the calibration 3 times. Will probably be running it again just to make sure. I don't know this receiver that well yet but as far as I can tell there are only 3...
  5. Replies
    16
    Views
    785

    Midrange on A7 vs. A9

    I recently purchased a pair of RTi A7's, and I've found these speakers to be fairly lacking in the midrange. I was considering exchanging them for a pair of A9's, but I'm wondering if anyone can...
  6. I'm no speaker expert by any means, but as you...

    I'm no speaker expert by any means, but as you say I think that kevlar would be much more durable than paper cones, given that the surrounds hold up. I think B&W also claims that the kevlar cones...
  7. Replies
    6
    Views
    572

    Thanks again gents, it looks like it won't be a...

    Thanks again gents, it looks like it won't be a concern. I had thought having the port so near to something might cause "chuffing" (which I have never experienced on a ported speaker BTW, have only...
  8. Replies
    6
    Views
    572

    Side Clearance for CSi A6?

    Does anyone happen to know about how much side clearance is needed for a CSi A6 center channel?

    I just ordered one, and in some of the pictures I noticed that the rear firing ports have the plates...
  9. Replies
    10
    Views
    912

    Changed the order to black speakers yesterday,...

    Changed the order to black speakers yesterday, they are supposed to be ready for pick up tomorrow. Thank you everyone for your input, you probably saved me from having to send the speakers back /...
  10. Replies
    10
    Views
    912

    I think I'm a little lost on what to do now.......

    I think I'm a little lost on what to do now.... :D

    Had called the local store yesterday, and told them to bring in their last pair of cherry A7's from their distribution center. Ten percent down...
  11. Half of the battle with soldering is keeping your...

    Half of the battle with soldering is keeping your tip clean and "wetted." Wetted meaning you always want there to be a nice layer of solder over the tip. Adding solder to the tip (or "tinning" the...
  12. Replies
    10
    Views
    912

    Well, after talking to a salesman at the local...

    Well, after talking to a salesman at the local shop, I think I'm going to go ahead with the A7's. What sucks is I can't actually look at the speakers until I put 10% down... they didn't have any...
  13. Replies
    10
    Views
    912

    :D Quarter sawn oak = far from drab. Trust...

    :D

    Quarter sawn oak = far from drab. Trust me.

    But yeah, may not be worth my time. Or, perhaps something I'll wait to do until they actually need it... have read that some people had issues...
  14. Replies
    10
    Views
    912

    Refinishing RTi A7's?

    Hello all, as you can see I'm a noob on the forum here. The question I have is in regards to the Polk RTi A7's - does anybody happen to have any experience refinshing these speakers, or know if...
Results 1 to 14 of 14