Search:

Shot in the dark here but have you tried different input on the receiver. Might be worth a shot. I have a denon 988 and use the ipod input without any problems.

Try both. Listen to each one for a week. Then go with the one you like better. This is very subjective and only you can determine this.

I don't think the 5503 is common ground. Seems like I read this somewhere but not sure where. I have a 5503 and I hooked the two negatives for left and right together. I have SDA1B and haven't had...

I have my amp(adcom 5503) plugged into my surge protecter(monster mkii 1100 I think) and haven't had any problems with it.

Personaly I would not make the sell. Craigslist is for local sale-face to face-cash and carry. I don't deal with paypal so I don't know the rules but seems like you would have to give them you...

I have the first one(monster) and have never had a problem with it. If there is a surge it will shut everything down until things return to normal.

I would pull the other crossover and compare the two just to make sure everything is where it should be. If everything is correct then I would start checking all my connections. After that -not sure.

I think I saw one on audiogon today. I didn't look at it just saw it listed. I think it was $325.00.

Ok I'll take a guess. The 55's have a vinyl finish and the 55i's have wood veneer. Also different drivers and crossover. I'm sure someone else can give you better details but it seems like I've read...

I have 1b's and I used a 9/32 bit. You have to be careful to be square. If you get off alittle you can go bigger like 19/64 if needed. My passive has 8 holes and I used them all. I did not use the...

You can purchase a blade/blade interconnect direct from polk. Just contact their customer service. Around $35-$40 . Not sure about the MW6510 but while you have them on the phone can't hurt to ask.

I would try some elmers glue. Maybe use some tape to hold it in place until it dries. If that don't work then I would try some contact cement. With contact cement you need to make sure it is where...

You can order a blade/blade interconnect cable from polk. Around $35-$40. Not sure about the pin/blade. If you give them a call I'm sure they will point you in the right direction.

I went with the clarity caps px series for my 1B's, 3-47uf and 2-22uf. These are some big caps and I had to mount them on a seperate board. There was also 2-34uf on the same board,2-22uf and 2-12uf...

If you check the vintage speakers section I think there may be a schematic there you can use.

Where are you located.

I have the same 14ga cable. I've been using it for 2 years now and don't have any problems with it. As far as sound goes my system sounds great to me. It could probably sound better if I had more...

I have fixed my problem--one out of phase. If you look in the vintage speakers section under the sda schematics at the bottom there is a troubleshooting guide where it tells you to use your balance...

Ok, I have a question about avr's. I had a problem with my sda 1b's and was looking at the troubleshooting guide in the vintage speakers section. I relize this is proably a old guide but it says to...

Yes you can. I have done it with my adcom 5503 and denon 988. Won't hurt anything.

I just purchased a sunfire cinema grand amp(200x5@8ohms). My question is this a common ground amp and ok to run sda's? I have done a search and found lots of info on both the sunfire and sda's and I...

HI, From what I've read they don't make the trilaminate tweeter anymore. I think the replacement is a silk dome tweeter. Unless you can find some used you might have to replace both of them so they...

Ok, Here's my say about it. Keep in mind that I'm a long ways from being any kind of expert. Set it up one way and listen to it. Does it sound good? Now try it the other way. does it sound better. If...

Hi Geoff, Nice job. I was wondering what you filled the gaps with and how hard was this to do. I'm going to do some 1B's and noticed they have the same gaps that you had and have been trying to...

Ok, Thanks Ben for your help also. It seems like I've read somewhere on the forum that dayton and solen didn't work well with the sda's. Is this true? Thats why I was going to go with clarity. I also...