Free Shipping on All Orders 1-866-764-1801

Vist our Online Store

Search:

Type: Posts; User: adam2434

Page 1 of 5 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thanks, was not aware that they have a lifetime...

    Thanks, was not aware that they have a lifetime warranty. I am the original owner, though I doubt I kept the receipt this many years.
  2. Replies
    56
    Views
    3,268

    Mantis, as I was dealing with all the issues, I...

    Mantis, as I was dealing with all the issues, I did listen to a single C275 with my LS90's and thought it sounded great - more than enough amp to drive them with ample dynamics and a balanced sound. ...
  3. Yeah, just one channel, and when I switch cables...

    Yeah, just one channel, and when I switch cables on the amp side, the issue follows the cable.

    I've had the T2's for 10+ years, and just recently noticed this. It is fairly subtle, but when I...
  4. MIT interconnects causing degradation of high freqs

    Anyone ever heard of MIT interconnects causing degradation of high freqs due to a failure/change in the cable?

    I have been troubleshooting reduced high freq output in one channel, and finally...
  5. Replies
    56
    Views
    3,268

    Well, my first and only NAD experience was a...

    Well, my first and only NAD experience was a nightmare.

    Three out of four C275BEE amps had issues - one with distortion in bridged mode, one DOA, and one with a right channel that faded in stereo...
  6. Replies
    56
    Views
    3,268

    Just recently bought my first NAD gear. Two C275...

    Just recently bought my first NAD gear. Two C275 amps from Spearit Sound and a C162 preamp (just won on eBay last night). I'll be running the C275s monobridged into LS90s, or may experiment with...
  7. Replies
    3
    Views
    218

    Thanks for the replies.

    Thanks for the replies.
  8. Replies
    3
    Views
    218

    LS90 binding posts vs. drivers

    Wondering if the upper posts are just for the tweeter when jumpers are removed.
  9. Need Help A source has to be able to drive the input of a...

    A source has to be able to drive the input of a preamp. So, if one's preamp input impedance and power amp input impedance are the same (or similar), then dynamics/authority should be similar whether...
  10. Need Help I've been doing a lot of preamp vs. no preamp...

    I've been doing a lot of preamp vs. no preamp comparisons lately.

    The variable output of an Emotiva DC-1 dac/pre connected to my amps sounds significantly different vs. the same DAC with fixed...
  11. I found this one, but the 2 RCA end looks pretty...

    I found this one, but the 2 RCA end looks pretty wimpy.

    http://www.markertek.com/Cables/Audio-Cables/Audio-Y-Cables-Y-Cables/TecNec/TN-P-2P-3.xhtml
  12. Vertical biamping RCA cable - 1 male to 2 male

    Did not find much of anything searching here or with Google...

    Anyone know where to get decent quality 1 RCA male to 2 RCA male cables for vertical biamping (rather than using a Y-splitter)?
    ...
  13. Replies
    3
    Views
    46

    Just went ahead and ordered 2 replacements so I...

    Just went ahead and ordered 2 replacements so I can have them mirrored on both speakers.

    CP discounted price is $60.
  14. Replies
    3
    Views
    46

    Driver for LS90

    Just discovered that the surround has separated from the cone about 3" on one LS90 driver. The adhesive failed.

    It probably could be re-glued, but I assume the entire surround would need to be...
  15. Replies
    40
    Views
    6,804

    View Post

    Hi, been a while since Iíve posted here.

    Recently picked up a set of RTi8ís for a modest, secondary system.

    I found them too bright for music, so after some research, experimented with Mills...
  16. Replies
    9
    Views
    671

    Yeah, I noticed a couple of his Wanee shows in...

    Yeah, I noticed a couple of his Wanee shows in the Live Music Archive at archive.org. Never heard of the Wanee Festival before that...what's that all about? A hippy, trippy, Woodstock kind of deal?
  17. Replies
    36
    Views
    1,763

    Really like my JVC HD250. Big improvement to...

    Really like my JVC HD250. Big improvement to black level and contrast over the Panasonic AE700 it replaced. I also really like the motorized zoom, shift, and focus...and the fact that it looks like...
  18. Replies
    9
    Views
    671

    Bobby Lee Rodgers

    Bobby Lee Rodgers

    Anyone heard of him?

    I buddy of mine saw him in a club while on vacation in Key West and told me to check him out. I'm glad he did.

    He is a tremendous guitar player that...
  19. Replies
    11
    Views
    792

    That's the Valab or Teradak non-oversampling DAC,...

    That's the Valab or Teradak non-oversampling DAC, right?

    A lot of folks have replaced the outputs caps (self included) in that DAC. Those are the larger, silver caps in your photo.
  20. Replies
    24
    Views
    1,049

    Always had a soft spot for the RTxxxi series with...

    Always had a soft spot for the RTxxxi series with the blue drivers and trilam tweeters, from the 25i on up to the towers.

    Still using a CS400i and FX500i's with my LS90's - they match quiet well....
  21. Replies
    124
    Views
    12,790

    I think he may be referring streaming FLAC...

    I think he may be referring streaming FLAC natively and having the SB convert to PCM vs. having the server software convert to PCM, and therefore streaming PCM.

    I've tried both ways and could...
  22. Replies
    5
    Views
    572

    Haha, I really don't see myself parting with...

    Haha, I really don't see myself parting with them. :biggrin:
  23. Replies
    5
    Views
    572

    Schematics attached.

    Schematics attached.
  24. Replies
    5
    Views
    572

    LS90 Crossover Mod

    I was thinking that it might be approaching the time to refresh/upgrade the crossovers in my LS90s, given that they're pushing 18 years old or so.

    Looking at the attached schematics, I was...
  25. Replies
    7
    Views
    1,426

    Need Help Crossover schematics are in a sticky at the top...

    Crossover schematics are in a sticky at the top of this forum page. However, it's best to verify the part values on the actual crossover.
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4