Free Shipping on All Orders 1-866-764-1801

Vist our Online Store

Search:

Type: Posts; User: RichCanDo

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. FYI I preferred the sound without the jumper, but...

    I preferred the sound without the jumper, but left it installed. It seems most have the jumper so I assume that it is as it should be. Leaving the jumper out may effect the circuit in other ways. -...
  2. FYI Thank you Mark for bringing this to the attention...

    Thank you Mark for bringing this to the attention of the Polk company. Nice to know they care about a product out of production for so long.

    Answer #1 provides the TL tweeters "hook up" in...
  3. Replies
    70
    Views
    3,726

    I agree with building your own as is much cheaper...

    I agree with building your own as is much cheaper and you can build specifically only for problem frequencies. At a library you can find books with info on building traps, etc. for specific...
  4. Replies
    11
    Views
    2,963

    What is a car audiophile? I remember reading when...

    What is a car audiophile? I remember reading when the owner of the Nakamichi Corporation was asked why he did not have one of his sound systems in his limousine, he replied the car was not good...
  5. Replies
    1
    Views
    421

    Sound quality? Proper location is required to...

    Sound quality? Proper location is required to obtain a good sound stage and imaging with any stereo speaker setup. It is probably the most important part of proper system set-up. Distance between...
  6. FYI 22.5? This is one of the resistor values. Looks...

    22.5? This is one of the resistor values. Looks like you have a .22uf Mundorf cap. - Schematic calls for .25uf. I received (2) .22uf Sonicaps that each measures .225uf. If I remember correct this...
  7. FYI No, not the brown one. The 22.5 ohm would be...

    No, not the brown one. The 22.5 ohm would be directly above it, about even with the closest edge of the inductor. Now under your caps. The body near the removed 750pf bypass cap. You have 3 resistors...
  8. FYI I would expect it to be correct if Ben did the...

    I would expect it to be correct if Ben did the work. I was waiting to learn if you found the 22.5 ohm resistor on the board or if it was removed. Now I am going to bed. Been awake all night.
  9. I was provided the schematic with link in post #4...

    I was provided the schematic with link in post #4 above. It is the correct one. Hopefully someone can post that one to the sticky.
  10. FYI Correct. That is the only jumper I had. Easy to...

    Correct. That is the only jumper I had. Easy to see where things go in photos I have in Post #1. Did you find the 22.5 ohm resistor? There should be 5 resistors on the board. (More if 2 were used to...
  11. FYI OK! Makes sense. My guess is the resistor was...

    OK! Makes sense. My guess is the resistor was removed with the bypass cap. Let me know if you find the 22.5 ohm resistor in the board.
  12. FYI Holes "C" and "D" are where the mica cap used to...

    Holes "C" and "D" are where the mica cap used to be. It was removed as not needed with upgraded caps. But hole "B" should have one lead of the 22.5 ohm resistor in it. If not in that hole, it should...
  13. FYI I edited the post you quoted above to state the 2...

    I edited the post you quoted above to state the 2 holes you were going to use are on the same trace.

    Pin #2 connects to a small trace. 12uf cap connects to this trace also. At the far end of the...
  14. FYI My 1.2TL #'s are 6119 & 61xx. Only a few replies...

    My 1.2TL #'s are 6119 & 61xx. Only a few replies so far with serial #'s, but looks like from my #'s and above have no jumpers. 50xx had correct factory jumpers.
  15. FYI Wrong holes. Those 2 holes are on the same trace....

    Wrong holes. Those 2 holes are on the same trace. The jumper connects the 2 traces together. But before you connect it, you need to know what is on that long trace. On stock board only one lead from...
  16. It looks as though Doro recently posted the...

    It looks as though Doro recently posted the CS1000p schematic to the sticky thread as the one listed has had no viewers yet. Thank you, but the WRONG SCHEMATIC WAS POSTED. It is the same as I think...
  17. FYI Look at the two photos I have marked with notes...

    Look at the two photos I have marked with notes in Post #1. It explains the connections. You can compare your board connections to it. Your parts may have been relocated, and connections made to...
  18. FYI I'm looking at schematics of my center CS1000p...

    I'm looking at schematics of my center CS1000p and f/x1000 surrounds to learn what it will cost to install new caps and resistors in them. Today I will probably install left over Dynamat on 5...
  19. FYI "I wish it was out now cuz it's a pain to take in...

    "I wish it was out now cuz it's a pain to take in and out"

    I had mine in and out many times also. In your last photo I see the inductor lead was relocated to the resistor hole. That resistor is...
  20. FYI If you have the crossover out, easy to check....

    If you have the crossover out, easy to check. Just look for 2 solder connections on the trace with Pin #2. One connection is the 12uf, other is either a jumper or lead of resistor. If only one solder...
  21. FYI It is hard to tell much from your photos of...

    It is hard to tell much from your photos of Jerry's board. It appears the jumper is missing as there is only one soldered connection on the trace connected to Pin #2. But it also looks like a few...
  22. FYI Yours are missing the jumper also. Your board...

    Yours are missing the jumper also. Your board looks just like mine did. Your jumper may be under the board but I doubt it is.

    What are the serial #'s on yours?
  23. FYI Yes, I would install the jumper as that is what...

    Yes, I would install the jumper as that is what the schematic calls for. If you upgraded to better capacitors, you can remove the 750pf mica bypass cap as others have stated is not really required...
  24. FYI Hi. The blue rectangle is in the proper location....

    Hi. The blue rectangle is in the proper location. It could be a jumper, though a simple piece of wire would have done the job. If a jumper, the type is used as to just quicken the installation,...
  25. I do not know where the thumbs down came from....

    I do not know where the thumbs down came from. Saw it after I posted. I had clicked the ? icon.
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4