Free Shipping on All Orders 1-866-764-1801

Vist our Online Store

Search:

Type: Posts; User: Mustang Matt

Search: Search took 0.00 seconds.

  1. Replies
    25
    Views
    3,230

    Need Help There's actually a separate Bi-amp statement. The...

    There's actually a separate Bi-amp statement. The one above says:
    "Run separate speaker wires to the low and high frequency drivers from a single amplifier"

    That's where I'm getting confused. It...
  2. Replies
    25
    Views
    3,230

    Need Help Yes, I've got all the other speakers wired up the...

    Yes, I've got all the other speakers wired up the way you described using both sets of post and no jumper. In all honesty I did it with the anticipation of eventually bi-amping.

    It makes sense...
  3. Replies
    25
    Views
    3,230

    Need Help But I was under the impression the speaker had an...

    But I was under the impression the speaker had an internal XO that came into the picture if you bi-wired it without the jumper. Is that incorrect?

    I completely understand where you're coming from....
  4. Replies
    25
    Views
    3,230

    Need Help It is in the same spot. What do you mean by...

    It is in the same spot. What do you mean by "normally and incorrectly using as bi-wire setup when the jumper plate is removed"? I followed the directions in the other LSi manuals that said to simply...
  5. Replies
    25
    Views
    3,230

    Need Help Right, I was thinking no examples of both pairs...

    Right, I was thinking no examples of both pairs of posts used without being bridged, but it's all making sense now that you guys have clarified it.
  6. Replies
    25
    Views
    3,230

    Need Help Yah it's starting to make sense. The manual...

    Yah it's starting to make sense. The manual doesn't even mention bi-wiring like the other speaker manuals do.

    I'm thinking this speaker deserved three sets of binding posts. In the end it probably...
  7. Replies
    25
    Views
    3,230

    Need Help Interesting. In figures 5,6, and 7 though none...

    Interesting.

    In figures 5,6, and 7 though none of them are using all four posts unless I am completely mis-reading. Based on what you've said where it would get converted back to line level...
  8. Replies
    25
    Views
    3,230

    Need Help In the manual, they don't show any configuration...

    In the manual, they don't show any configuration using all four binding posts that I see.

    In addition, my current configuration with one pair of wires going from the amp to the top set of posts...
  9. Replies
    25
    Views
    3,230

    Need Help I have an LSi25, C, FX, 9 7.1 setup with a...

    I have an LSi25, C, FX, 9 7.1 setup with a velodyne vrp-1200 sub.

    Currently have 5 channels powered by an outlaw 750 and the two rear channels powered by an sc05 pioneer elite receiver.

    All...
  10. Exactly. Thanks a bunch!

    Exactly. Thanks a bunch!
  11. Any references? Not sure what you mean and...

    Any references? Not sure what you mean and neither does google. :)
  12. Looking for recessed angled speaker wall plates

    Has anyone seen a wall plate that looks similar to the back of a LSI series speaker with 4 posts recessed and angled?
  13. Yes! I've been too busy listening to it to reply!...

    Yes! I've been too busy listening to it to reply!

    The only problems I'm having are:
    1. As I increase the volume I start to get a bit of crackle coming through. Seems like it happens with any...
  14. Replies
    18
    Views
    1,502

    FYI Yah I picked up a LSiC, pair of LSiFX, a VRP-1200...

    Yah I picked up a LSiC, pair of LSiFX, a VRP-1200 all used for $900 shipped a couple weeks ago. The rear corner of one of the LSiFX took a hit during shipping so I think I'm going to end up getting...
  15. Replies
    47
    Views
    2,732

    I setup my LSi9/LSiC/LSiFX combo tonight with an...

    I setup my LSi9/LSiC/LSiFX combo tonight with an outlaw 750 amplifier. This amp is rated 5 x 165 @ 8 Ohm and 5 x 250 @ 4 Ohm. Sounds great to me! I bought it used for $550 shipped with BJC...
  16. Replies
    93
    Views
    6,280

    I received my front LSi9s in today and set...

    I received my front LSi9s in today and set everything up. (sounds fantastic! I'm loving the sc-05 so far!)

    I'm running all 5 LSi speakers off an outlaw 750. After all the reading I've done, I'm...
  17. Replies
    18
    Views
    1,502

    FYI $440 shipped. The seller had the UPS store pack...

    $440 shipped. The seller had the UPS store pack them quite well. They arrived today and sound absolutely fantastic!!!!
  18. Replies
    18
    Views
    1,502

    FYI I bought the ones on audiogon. Should be here on...

    I bought the ones on audiogon. Should be here on Wednesday.
  19. Replies
    93
    Views
    6,280

    Just ordered my sc05 from videogon....

    Just ordered my sc05 from videogon.
    http://cgi.videogon.com/cgi-bin/cl.pl?rcvr71ch&1240339335

    The guy is an authorized reseller.

    Should be here Wednesday I think.
  20. Hey Everyone, Thanks for the welcomes and all...

    Hey Everyone,

    Thanks for the welcomes and all the useful information! I've been reading my eyes out. At this point I'm leaning towards the pioneer sc-05. All of the receivers listed and being that...
  21. Thanks for the advice guys. I will do some...

    Thanks for the advice guys. I will do some research on these models tomorrow.
  22. Need recommendations on receivers with pre-outs under $1000

    My setup:
    2xLSi9
    1xLSiC
    2xLSiFX
    VRP-1200 sub
    Outlaw 750 Amplifier
    PS3
    Wii
    KDS60A3000
  23. Replies
    47
    Views
    2,732

    I'm in the exact same boat. I bought an lsic and...

    I'm in the exact same boat. I bought an lsic and pair of lsifx with plans to get a pair of lsi9 to replace my r50 mains.

    Now I need a receiver and an amp to power it all.

    If I were to buy...
Results 1 to 23 of 23