Free Shipping on All Orders 1-866-764-1801

Vist our Online Store

Search:

Type: Posts; User: gaspipe

Search: Search took 0.00 seconds.

  1. Replies
    51
    Views
    4,119

    When I was working through my XO issues, I...

    When I was working through my XO issues, I changed some pm's with Trey. I still want to upgrade the XO's in mine too. It's hard to imagine better sound until you have it. :D
  2. Replies
    51
    Views
    4,119

    Blowing the dust off this thread.... I've had...

    Blowing the dust off this thread....

    I've had my Linbrook Signatures for a year or so now. At first, I was planning to flip them because I got them fairly inexpensively because they had a...
  3. Replies
    41
    Views
    3,804

    Did you get the Bose EQ that came with them from...

    Did you get the Bose EQ that came with them from the factory? That's the key for making them reproduce anything close to normal sound. The Series 1 & 2 had very different eq curves than the later...
  4. Need Help Pic of the network....just for the record. :wink:...

    Pic of the network....just for the record. :wink:

    I can't help but think there's some room for improvement in here.

    http://gaspipe.smugmug.com/Electronics/XL280/i-MqcrTLK/0/L/tyler-001-L.jpg
    ...
  5. Need Help I'm betting you're correct that Ty wouldn't have...

    I'm betting you're correct that Ty wouldn't have made that mistake. It was obvious someone was in there at some point, and also replaced a fried voice coil once before I was in there. The solder...
  6. Need Help TY, GD. I can't imagine that running the...

    TY, GD.

    I can't imagine that running the signal through a 1 ohm resistor and not going through the bypass caps would be good. I'm not an EE, but it surely seems like the 'bad' speaker XO was an...
  7. Need Help The 8" driver issue is both drivers appear to...

    The 8" driver issue is both drivers appear to have bent center sections, and there's some rubbing. That's gonna be expensive to fix @ $240 each :(
  8. Need Help Hey Beef Jerky, that's darned good thinking, and...

    Hey Beef Jerky, that's darned good thinking, and here's what I found: On the speaker with the very 'lively' tweeter, which had a blown voice coil, this is the XO:
    ...
  9. Need Help Thanks Stuwee. That's a good plan. I haven't...

    Thanks Stuwee. That's a good plan. I haven't spoken with Ty in a good long while, so likely best to chat with him. I'm just not really familiar with the Seas drivers. :smile:
  10. Need Help I have a pair of TriTrix TL's I built running on...

    I have a pair of TriTrix TL's I built running on those amps now. They are substantially less robust than these monsters. If one of the amps is getting wonky, they should melt the Daytons in the...
  11. Need Help Thanks for the consideration George. I...

    Thanks for the consideration George.

    I thought that at first, but bias and dc are good on the Haflers. I even swapped amps. Definitely one tweeter has a much greater excursion than the other. I'm...
  12. Need Help Tyler Acoustics Linbrook Sig's - SEAS tweeter or XO issue?

    Long time lurker here. I know some of you have had quite a bit of experience with Seas drivers and Ty's offerings, so perhaps you all might have some thoughts on the matter.

    I bought a set of the...
  13. Replies
    202
    Views
    29,758

    I know this thread is old, but to answer this, I...

    I know this thread is old, but to answer this, I used clarity caps and mills 2 ohm resistor both ways with/without the switch in my 5B's (no fuse). I could not hear a definitive difference, so I put...
Results 1 to 13 of 13