Free Shipping on All Orders 1-866-764-1801

Vist our Online Store

Search:

Type: Posts; User: biggs

Search: Search took 0.00 seconds.

  1. Thread: Burnt line-outs?

    by biggs
    Replies
    2
    Views
    1,104

    Burnt line-outs?

    Had a little mishap the other day during a full-open acceleration. Somehow the +cable got yanked out of the distribution block. When I hooked it up again, I got hissing on all channels. Disconnected...
  2. Replies
    8
    Views
    2,110

    Do you have HPF/LPF switched on at reciever and...

    Do you have HPF/LPF switched on at reciever and amp?
    List your settings please.
  3. Replies
    7
    Views
    1,971

    Could it be a ground issue? Checked your...

    Could it be a ground issue? Checked your groungingpoint?
  4. Replies
    28
    Views
    2,087

    Scripture quoted for car stereo. That's gotta be...

    Scripture quoted for car stereo. That's gotta be a first?
  5. Replies
    8
    Views
    2,110

    HPF at 100Hz? Did you mean LPF?

    HPF at 100Hz? Did you mean LPF?
  6. Replies
    11
    Views
    1,367

    Just to make sure. You did connect power and...

    Just to make sure. You did connect power and ground to the amp? Also, it requires a remote-turnon lead from the headunit to the remote input on the amp, so it'll turn on when you start your headunit....
  7. Replies
    10
    Views
    1,780

    HU only allows 50/80/125Hz, so that's not an...

    HU only allows 50/80/125Hz, so that's not an option. I too would think my components deserve a better HU...but it's a very cool unit =) I guess I'll ponder for a while and check how much I can get...
  8. Replies
    10
    Views
    1,780

    Revisiting this one to say thanks for the help. ...

    Revisiting this one to say thanks for the help.

    And of course some more questions ;p

    I tried using just the x-over in the HU. 80Hz for both HP and LP. 12dB HP and 18dB LP (only option on my...
  9. Replies
    3
    Views
    1,582

    It's in there, page 15. Supposing you have two...

    It's in there, page 15.
    Supposing you have two 4ohm SVC subs that is. Sub 1 to speaker 1 on the amp, sub 2 to speaker 2 on the amp. Now they're wired in paralell presenting a 2ohm load.
  10. Replies
    10
    Views
    1,780

    Okay, so the slope settings rolls the volume down...

    Okay, so the slope settings rolls the volume down on the mids where it intersects with the sub and vice versa? Should I leave the HPF and LPF on the source switched off and let the amps do the...
  11. Thread: new member

    by biggs
    Replies
    24
    Views
    2,176

    Ah, internet forums. It makes the hours on...

    Ah, internet forums. It makes the hours on nightshift fly.
  12. Replies
    10
    Views
    1,780

    Momo amp settings

    So, I'm not Robert, but maybe you could be at my service too MacLeod.

    So I have a c300.2 for my SR6500's, and a c500.1 for my MTX Thunder 7510-44 10".
    Everythings ready to go in the car, cables...
  13. Replies
    5
    Views
    1,139

    Ok, thanks for the input. Got the second c300.2...

    Ok, thanks for the input.
    Got the second c300.2 anyway, might get some sr5250's in a while and build a pod, either up front or the rear door panels.

    Got everything installed today, but ofcourse...
  14. Replies
    5
    Views
    1,139

    The crossovers are "bi-amp ready", no? So one...

    The crossovers are "bi-amp ready", no? So one c300.2 for the woofers and one for the tweeters, then via the crossovers. Set the HU at 3/4 volume and the gains on the amps to minimum, then work from...
  15. Replies
    5
    Views
    1,139

    Oh, my HU is an AVIC-HD3BT

    Oh, my HU is an AVIC-HD3BT
  16. Replies
    5
    Views
    1,139

    Dual Polk/momo c300.2 driving sr6500 set?

    Ok, tried to search for something like this but couldn't find any.

    So I have a c300.2, and sr6500 on the way. Also I have a c500.1 for my 10" MTX 7500 DVC sub.

    Now, I can get another brand new...
Results 1 to 16 of 16