Free Shipping on All Orders 1-866-764-1801

Vist our Online Store

Search:

Type: Posts; User: Jed Leland

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    95
    Views
    2,915

    Mine is from a character in Citizen Kane.

    Mine is from a character in Citizen Kane.
  2. Replies
    4
    Views
    2,270

    Need Help Hey Mike, One cause could be a faulty volume or...

    Hey Mike,
    One cause could be a faulty volume or balance control. Does the problem get better or worse as you turn the volume control? Does the receiver have a pre-amp out/power amp in connection on...
  3. Replies
    3
    Views
    627

    Need Help Hello, I'm not a hundred percent sure, but I...

    Hello,
    I'm not a hundred percent sure, but I don't believe so. But, you should check with Polk.
    Ken
  4. Replies
    3
    Views
    627

    Need Help Hello, To begin advancing the time, once you...

    Hello,
    To begin advancing the time, once you have set the correct time unplug the AC power supply. Then, after a second, reconnect the power supply and the time will begin advancing.
    You'd have to...
  5. Replies
    1
    Views
    1,444

    Hello, Thanks for posting on the Forum. It is...

    Hello,
    Thanks for posting on the Forum. It is possible your TV is producing a small amount of noise that is preventing the auto on/off from working. You can test this by removing the audio...
  6. Replies
    29
    Views
    7,327

    Need Help Hello, Those circuit path resistors look like...

    Hello,
    Those circuit path resistors look like Corning glass composition types. We used those on the original Dyna PAS 3X and ST70 mods, way back when. They were certainly an upgrade from carbon...
  7. Replies
    56
    Views
    2,132

    Happy Birthday, Cathy!

    Happy Birthday, Cathy!
  8. Replies
    6
    Views
    981

    Need Help Hello, If it is a true digital cable, the RCA...

    Hello,
    If it is a true digital cable, the RCA plug itself would have to have a 75 ohm impedance as well as the cable. The dielectric used in the RCA plug would have to have a 75 ohm impedance at RF....
  9. Replies
    9
    Views
    1,700

    Hello, With all due respect, I don't believe...

    Hello,
    With all due respect, I don't believe ignoring it is a good idea. The auto-calibration system is measuring something. There is a dip in the frequency response or a difference between the...
  10. Replies
    9
    Views
    1,700

    Hello, The problem could be the relationship...

    Hello,
    The problem could be the relationship between the right speaker and the sub-woofer. The auto-calibration could be seeing a bass cancellation and reading this as "out-of-phase" between the...
  11. Replies
    6
    Views
    981

    Need Help Hello, Are you looking for an RCA plug that will...

    Hello,
    Are you looking for an RCA plug that will go on the end of a coaxial cable and have a characteristic impedance of 75 ohms? Not quite sure what you're looking for?
    Cheers, Ken
  12. Replies
    44
    Views
    8,692

    Hello Andy, I'm afraid it didn't scan very well....

    Hello Andy,
    I'm afraid it didn't scan very well. But, I have made a copy, so if you'll give me your snail mail address I can send it. You can contact me at kenswauger@tapepath.com
    I don't think the...
  13. Replies
    44
    Views
    8,692

    Hello, I can ask my wife to scan the article and...

    Hello,
    I can ask my wife to scan the article and I can send it to you. PM me your address and I'll send it.
    Ken
  14. Replies
    44
    Views
    8,692

    Hello Andy, The first amp is finished and the...

    Hello Andy,
    The first amp is finished and the second one is completed except for cleaning and painting the AC transformer. The bell housings for this transformer have been powder coated and only...
  15. Replies
    14
    Views
    2,913

    Hello, There isn't a parallel connection because...

    Hello,
    There isn't a parallel connection because the crossover isolates each section of the speaker from the other. If an incoming sound were 100Hz, for example, the low pass section of the...
  16. Replies
    14
    Views
    2,913

    Hello, The speaker's impedance will remain the...

    Hello,
    The speaker's impedance will remain the same no matter how many amplifiers you connect to it or how many speaker wires you use between the amplifier and the speaker. The speaker's impedance...
  17. Replies
    2
    Views
    806

    Need Help Hello, The speaker level output, on the...

    Hello,
    The speaker level output, on the sub-woofer, will not be active unless you make a speaker level input connection to the unit. In other words, the only way to get a signal coming from the...
  18. Replies
    9
    Views
    1,169

    No problem! Take care.

    No problem! Take care.
  19. Replies
    9
    Views
    1,169

    Hello, The Canadian manager is Walter Moser, a...

    Hello,
    The Canadian manager is Walter Moser, a great guy. You can email him at wmoser@polkaudio.com and I'm sure he'll help.
    Cheers, Ken
  20. Replies
    36
    Views
    1,118

    Merry Christmas, everyone!

    Merry Christmas, everyone!
  21. Need Help Hello, I agree with the other members, the amp...

    Hello,
    I agree with the other members, the amp seems to be in the bridged mode. That would be the most likely explanation that could cause the result. It "thinks" you want it to only produce a...
  22. Need Help Hello, Sometimes when I have a problem to figure...

    Hello,
    Sometimes when I have a problem to figure out I go about it from the unwanted results backwards. In other words, I try to think how I could make what is happening happen if I wanted to. In...
  23. Hello, If the SDA cable is defective there won't...

    Hello,
    If the SDA cable is defective there won't be any sound produced by the SDA drivers. This would be the outside drivers of each speaker. You would need to check the SDA cable for end-to-end...
  24. Replies
    43
    Views
    1,540

    Excellent news! That's great! Take care...!

    Excellent news! That's great!
    Take care...!
  25. Replies
    19
    Views
    4,171

    Need Help Hello, One approach is to take one of the...

    Hello,
    One approach is to take one of the resistors and bend its leads at right angles so it fits into the holes in the circuit board. Then turn the circuit board over and solder the leads to the...
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4