Thanks for the offer to make this for everyone. I'd like a set for SDA 2.3 and SDA II (A type with one tweeter and two mids per speaker) Thanks.
Buy Direct M-F 9am - 10:30pm EST 1-866-764-1801
Vist our Online Store
+ Reply to Thread
Results 31 to 60 of 348
-
06-08-2010 11:44 AM #31
Rings
-
06-08-2010 01:47 PM #32
Right now on just the 6.5" rings the cost I have it quoted for will be $5.80 ea. + shipping + 3% paypal if you choose to pay with paypal.. Now if we had a thousand of these going out the door the cost would drop big time..
I figured this would give some of you an idea what it will cost just to do your drivers....
Keep in mind:
Material cost,
Laser cut time,
Hardware cost,
Installing hardware time.
Pack and ship...
I will just run this through the shop as a job...
When I did the crossover plates my boss let me have some drop aluminum to make them with, and that saved those of you guys that got them a lot of money. That and I cut and time saved them myself, and did it on my own time..Sometimes.. late at nite... I fill my bathtub with tomato sauce and pretend I am a meatball.
-
06-08-2010 01:54 PM #33
Is this a one time thing? Will there be an opportunity down the road to get these? If not then I can up my order count.
-
06-08-2010 01:57 PM #34Member Sales Rating: (12)
- Join Date
- Nov 2008
- Location
- Watchin' GBTV... the TRUTH LIVES HERE!
- Posts
- 11,091
Have you got a cost for the 15" passives yet?
HT Setup... Pioneer Elite SC-37, Polk Audio SDA-SRS 1.2TL's Restored with full mods, Polk Audio RM-7500 Surrounds, Oppo BDP 93
Two Channel... Carver Statement 450~1 Vacuum Tube Monoblocks, Dodd Mid-line Tube Linestage with Psvane 12Ax7 tubes, Pioneer Pdd 9Mk II SACD Player, Yamaha PX-3 Turntable with Sumiko BPS EvoIII, Polk Audio SDA-SRS 1.2TLs, with full mods.
Benghazi was more than just FUBARED...
-
06-08-2010 02:38 PM #35
Price seems reasonable... I'm still in!
Ludicrous gibs!
-
06-08-2010 02:40 PM #36
Originally Posted by TOOLFORLIFEFAN
Sounds good!!
-
06-08-2010 02:45 PM #37
Count me in for a pair of 1Cs and Monitor 7s.
-
06-08-2010 02:58 PM #38
Originally Posted by audiobilly
No I plan to keep the program, and some on the side just in case...;)Sometimes.. late at nite... I fill my bathtub with tomato sauce and pretend I am a meatball.
-
06-08-2010 03:04 PM #39
Cool Larry, that means I wouldn't have to buy them all at once and go broke. I could do one set of speakers at a time. Much better.......
Greg
-
06-08-2010 03:10 PM #40
Six bucks a pop seems very reasonable to me. Now to find out what the PR ring would cost. Originally Posted by TOOLFORLIFEFAN
-
06-08-2010 06:12 PM #41
The PRs will require a lot of real estate on the sheet metal. Unless you could cut at least one mid driver out of the middle, maybe two on the 15 inchers. Let's just hope Polk was accurate with their hole drilling.
>
>
>This message has been scanned by the NSA and found to be free from harmful intent.<
-
06-08-2010 06:29 PM #42
that shouldn't be a big deal. Worst case you could fill the original holes and drill new ones. Originally Posted by Polkersince85
-
06-08-2010 10:12 PM #43
I'll take complete sets for a pair of 2.3TL's, 2B's and CRS+'s. If you are selling the bolts as well, I would like black ones.
'Political Correctness'.........defined
"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end."
-
06-08-2010 10:22 PM #44
If you are selling the bolts, I want a set of black and a set of brass.
"Polk SDA-SRSs are hopelessly out of date both sonically and technologically... I see no value whatsoever in older SDA speakers."~Audio Asylum Member
__________________
"Knowledge, without understanding, is a path to failure."~DK
-
06-08-2010 10:30 PM #45
I'll take a set for my SDA-1C's with black hardware.
-
06-08-2010 10:30 PM #46
Is brass on the table too?
'Political Correctness'.........defined
"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end."
-
06-08-2010 11:12 PM #47
Would the bolts not be of a standard thread size/pitch that you could get them from your local hardware store?
Ludicrous gibs!
-
06-08-2010 11:18 PM #48
If any thread pitch is involved, you should keep it 1/4-20....since almost everything Polk is of that measurement.
-
06-08-2010 11:29 PM #49
Not sure but could the PR be cut in 4 pieces to save on scrap and size for shipping.
I hope you could add the screws for us overseas guys. Brass, black or gold plated :p
I really appreciate you offering this!
-
06-09-2010 12:10 AM #50
I have some concerns with doing the passives for all models.
The SRS,1.2,1.2tl and the 1C's of course are no problem. And I have a passive for the monitor 7's so no problem there as well.
So I need help with the other models. I'm sure the passive in the 1C's is the same in one in the SDA 2B's.
No reason to worry about where Polk drilled there holes I will send a drill template with the set.
So some help from you SDA gurus would help.Sometimes.. late at nite... I fill my bathtub with tomato sauce and pretend I am a meatball.
-
06-09-2010 02:58 AM #51
Larry, the SDA SRS 2, 2.3, 2.3TL, SDA SRS, 1.2 and 1.2TL all use 15" PR's. All the CRS versions are 10". All the rest are 12". I can make a template for the 10" if you need me to.
'Political Correctness'.........defined
"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end."
-
06-09-2010 03:08 AM #52
Larry, count me in for a set for my 2A's.
That would be four MW's, and two 12" PR's.
I'll probably get a set for my M7's eventually too, but the SDA's take priority.
$6 a pop seems VERY reasonable to me.:)
You're one of the ones at the forefront of SDA tweaking. Keep up the good work!The nirvana inducer-
APC H10 Power Conditioner
Denon DVD-2910 universal player
DPA The Little Bit Three DAC
Yamaha P-300 turntable/TCC TC-750 phono preamp
Acurus L10 preamp
Adcom GFA-545 power amp
PolkAudio SDA 2A's/PolkAudio Monitor 7A's
Audioquest Type 4 speaker cables
Audioquest Sidewinder IC's
Audioquest Black Mamba IC's
Signal Cable Analog II IC's
-
06-09-2010 03:19 AM #53
Any love for the SRT's?
I'm placing an order for my Sda's.
1.2tl, srs 2, srs 2.3tl, srs 3.1tl, sda 1c, crs +.
One complete set each plus black bolts if available.
At a later date I will do all my monitor series. I have too many of those to do right away.Last edited by ESavinon; 06-09-2010 at 03:25 AM.
SRT For Life; SDA Forever!
The SRT SEISMIC System:
Four main satellite speakers, six powered subs, two dedicated for LFE channel, two center speakers for over/under screen placement and three Control Centers. Amaze your friends, terrorize your neighbors, seize the audio bragging rights for your state. Go ahead, buy it; you only go around once.
-
06-09-2010 03:34 AM #54
Cool Jesse. I knew you'd come through with the stats. Originally Posted by F1nut
By the way, Larry. I think you'll need a lot of black bolts (and some brass ones too).
Greg
-
06-09-2010 03:47 AM #55
Was there ever even an iota of a doubt?;) Originally Posted by headrott
-
06-09-2010 03:48 AM #56
In for a pr. of SRS 2's.
-
06-09-2010 01:46 PM #57Member Sales Rating: (0)
- Join Date
- Jan 2010
- Location
- At the golf course eating mushrooms!
- Posts
- 1,130
I've in for a full set for a pair of 1C's with black allen head bolts.
Just need to know how you want to do this.
Can you ship them so i can get them like yesterday :D"50% Why... That's almost half."
"I know, I'm sick and need help."
----
www.gimpod.com
----
"The best way to enjoy digital music reproduction is to never listen to good analogue reproduction." ~ Kenneth Swauger
-
06-09-2010 11:32 PM #58
1 set for SDA2B's MW and PR also for tweets if you do them too.
-
06-09-2010 11:40 PM #59
1 set for SDA2B's MW and PR also for tweets if you do them too.
-
06-10-2010 06:15 AM #60
"Ok" I have the Dimensions for the 10" 12" and 15" passives.
Thanks Jesse!!
On the 10" passive did Polk ever use all 8 holes in any of the models? I will hardware for all eight but I was just curious.
This might seem slow for me to get all of this together, but I am slammed at work right now. As soon as I have everything ready to roll I will start going through the list and get PM's to to you guys. I don't want to hold on to your money to long, I want you guys to be able to pay and know you will see them within two weeks max.
Thanks for being patient,
Larry.Sometimes.. late at nite... I fill my bathtub with tomato sauce and pretend I am a meatball.
Reply With Quote
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Gaskets for MW6XXX
By brgman in forum Vintage SpeakersReplies: 115Last Post: 10-13-2011, 10:58 PM -
Wanted 2 SW 120 passives
By geppy1 in forum Wanted (WTB) ClassifiedsReplies: 2Last Post: 01-31-2011, 11:26 PM -
Round 4 Rings for Drivers and Passives.
By Toolfan66 in forum Vintage SpeakersReplies: 61Last Post: 11-29-2010, 08:57 AM -
For Sale Round 3 Rings for your Drivers and Passives..
By Toolfan66 in forum For Sale (FS) ClassifiedsReplies: 60Last Post: 09-29-2010, 11:24 AM -
For Sale Passives---from 11 T----50.00 shipped
By george daniel in forum For Sale (FS) ClassifiedsReplies: 5Last Post: 10-07-2008, 06:21 AM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts