Free Shipping on All Orders 1-866-764-1801

Vist our Online Store
+ Reply to Thread
Results 1 to 3 of 3
  1. #1

    Member Sales Rating: (0)

    Join Date
    Jul 2011
    Location
    Tallahassee, FL
    Posts
    5

    Default PA D5000.5 setup questions

    Ok, it was 15 years ago when I last dealt with custom stero installations so ignore the lack knowledge here because I have forgotten a few things or they simply were not an option on the amp I used way back then compared to now.

    Everything is finally installed, minor brain fart with my F/R crossover being wired wrong and no engine noise so no filters required thank God! Needs some tips on the amplifier setup.

    Here is what I have questions about...

    1. level Control: My HU has three sets of 4 volt pre-amp outputs. How do I set the level control on the amp for the sub, the front and rear speakers? I turned it to 6V and then backed it off to what I think is around 4 volt. Can I use the voltmeter to check the signal being output on the speaker wires to get the actual voltage?

    2. SUB Sonic filter and LPF Control: I am setting this by my own intuition and what I think sounds good

    3. Full, HPF and BPF switch: I set front and rear speakers to HPF. Manual said this seeting is for midrange and tweeters. Since all four doors are DXI6500 components with crossovers I assumed this is the correct setting. Any advice would be welcomed here.

    4. Frequencies: Anyone have any recommended settings for these or should I just play with the settings until it sounds good to me. Obviously I don't want too low of a frequency going to the 6.5's since I have a woofer to handle that.

    Thanks guys for the input!

  2. #2

    Member Sales Rating: (0)

    Join Date
    Feb 2010
    Location
    NY
    Posts
    698

    Default

    1. yes, you can use volt meter. Keep in mind that you only get 4v at max volume (that is if you ever do to begin with, most units don't make advertised voltage in real world use)
    2. yes but there are basic "rue of thumb" - cut you subwoofer at 50-60-80Hz. If you want sound quality (aka SQ) there is.
    3. yes, HPF is what you need in this set-up. Same as sub's crossover it shoud be somewhere in 50-60-80 range. With DXi it's probably 60-80.
    4. as i said before - 50-60-80Hz.
    2008 Nissan Altima
    Kenwood DNX 5140
    Arc Audio IDX and XEQ
    Polk Audio SR6500 active and SR124-dvc sealed
    Polk Audio PA500.4 and PA1200.1

  3. #3

    Member Sales Rating: (0)

    Join Date
    Mar 2009
    Location
    Columbus, OH
    Posts
    147

    Default

    Set the gain by ear. A HU will only output 4V when running a sine wave/test tone at max output. Real music is dynamic and a HU that is rated for 4V will normally output between 1-1.5V during music. So if you were to match up the gain to 4V on the amp it will not be loud enough and the amp won't be optimized.

    1. Find out what volume the HU clips. Turn the amp gain all the way down, and then turn up the HU volume until the sound changes. What will happen is that instead of there being a nice balanced sound with lows and highs, the signal gets clipped compressing the middle together. It will sound bad at this point. My Kenwood x595 doesn't clip even at full and my last Pioneer didn't either. If you don't find the max clean volume you are not sending the amp an optimal signal.

    2. Now turn your HU to the max unclipped volume. Now slowly turn up the gain until the same clipping occurs.

    Hopefully your HU doesn't clip. If it does take it back a notch or two to where it sounds good again. Repeat on the amplifier.

    The old 3/4 volume rule on the HU is ok to use but is an old technique that isn't very good on new head units as many of them don't clip or clip very close to max volume.
    Audison Bit Ten
    Kenwood X595
    Polk MM6501
    Polk MM1240
    Mtx 704x
    Alpine MRX50

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Similar Threads

  1. PA D5000.5 speaker and sub with different Ohm rating question
    By bbmxta in forum Car Audio & Electronics
    Replies: 4
    Last Post: 02-01-2012, 02:58 PM
  2. Pioneer app radio And PA D5000.5 best connection solution
    By brandoncurran in forum Basic Hookup/Wiring Questions
    Replies: 0
    Last Post: 01-01-2012, 08:57 PM
  3. RTI-12 Setup Questions
    By Enzo2400 in forum Speakers
    Replies: 15
    Last Post: 04-13-2009, 11:45 AM
  4. New amp and setup questions
    By Nick14874 in forum Car Audio & Electronics
    Replies: 8
    Last Post: 03-31-2008, 12:46 AM
  5. New Setup Questions??
    By reubenray in forum Speakers
    Replies: 3
    Last Post: 02-25-2006, 09:20 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts