Free Shipping on All Orders 1-866-764-1801

Vist our Online Store
+ Reply to Thread
Results 1 to 11 of 11
  1. #1

    Member Sales Rating: (0)

    Join Date
    Oct 2013
    Posts
    3

    Default I want to know what Qms

    I want to know what Qms, Vas and Qes means?

  2. #2

    Member Sales Rating: (2)

    Join Date
    Jun 2004
    Location
    New England
    Posts
    8,291

    Default

    These are three of the parameters used to quantify the performance characteristics of a loudspeaker driver; three of the so-called "Thiele-Small" parameters. The T-S parameters are used to "fit" a driver to an enclosure (or, to think about it conversely, to "tune" an enclosure to a given driver). Arguably, the full gamut of T-S parameters is most important for woofers, but in practice the parameters may be determined for any driver and may be useful for MR and tweeters, too - if for no other reason than to select crossover frequencies.

    Here's a personal favorite primer on measurement of T-S parameters. It identifies the important parameters, even if the definitions given are a bit circular :-)

    http://sound.westhost.com/tsp.htm

    Definitions:
    Re Electrical [i.e., DC] resistance of voice coil
    Fs Resonant frequency of loudspeaker moving mass (in free air)
    Qes Electrical Q of loudspeaker ["Q" describes the shape of the peak of the impedance curve around Fs (see the figure below) - high "Q" = high, sharp "mountain peak"; low "Q" = broad, low "hill"]
    Qms Mechanical Q of loudspeaker
    Qts Total Q of loudspeaker [see the link to see how Qms and Qes relate to Qts]
    Vas Equivalent air volume of moving mass suspension [this is a measure of the compliance or, I ould say, the "floppyness" of the driver's suspension]



    Note the impedance peak around Fs - this is the "Q" curve. The impedance is fairly flat around 100 to 200 Hz; this is where the "nominal" impedance figure comes from. At higher frequencies, the impedance rises due to the "inductance" of the speaker's voice coil.

    There are some very good books on the subject of loudspeaker (enclosure) design - I like David Weems' books and Ray Alden's books. Vance Dickason's Loudspeaker Design Cookbook is another classic design reference.

    EDIT: Google turned up some more explanatory pages :-)
    http://www.speakerplans.com/page89.html
    http://www.eminence.com/support/unde...dspeaker-data/
    Last edited by mhardy6647; 11-01-2013 at 07:21 AM.
    all the best,
    mrh

  3. #3

    Member Sales Rating: (1)

    Join Date
    Aug 2009
    Location
    central Illinois
    Posts
    3,564

    Default

    bet this went zoom right over their head:)

  4. #4

    Member Sales Rating: (2)

    Join Date
    Jun 2004
    Location
    New England
    Posts
    8,291

    Default

    ahh, well... we do what we can. That "speakerplans dot com" has a pretty good nontechnical explanation of what the parameters mean.
    all the best,
    mrh

  5. #5

    Member Sales Rating: (0)

    Join Date
    Dec 2003
    Location
    Chattanooga, TN
    Posts
    11,825

    Default

    Ive been in this hobby since 1988 and the sport as a competitor since 2005 and I STILL dont have a clue what all this T/S parameters is about. All I know is that you need a Qts of .40 or higher to run a speaker in infinite baffle and .71 Qts is considered perfect (flat). I kinda know what resonant frequency (Fs) means that basically it shows you how competent the driver is at lower frequencies like a tweeter with a Fs of 750 like the Scan Illuminator is going to work a lot better crossed over at 2.5KHz than a LPG 26NA with its 1500 Hz FS. But thats about it as far as my knowledge goes. I stick to the calculators like WinISD to do all the legwork.
    Last edited by MacLeod; 11-02-2013 at 09:39 PM.
    polkaudio sound quality competitor since 2005
    MECA SQ Rookie of the Year 06 ~ MECA State Champ 06,07,08,11 ~ MECA World Finals 2nd place 06,07,08,09
    08 Car Audio Nationals 1st ~ 07 N Georgia Nationals 1st ~ 06 Carl Casper Nationals 1st ~ USACi 05 Southeast AutumnFest 1st

    polkaudio SR6500 --- polkaudio MM1040 x2 -- Pioneer P99 -- Rockford Fosgate P1000X5D

  6. #6

    Member Sales Rating: (31)

    Join Date
    Feb 2007
    Location
    Long Island
    Posts
    14,789

    Default

    Here are some much more advanced "calculators": http://audio.claub.net/software/jbabgy/jbagby.html

    Woofer Box and Circuit Designer makes WinISD look like a toy.
    "He who fights with monsters should look to it that he himself does not become a monster. And when you gaze long into an abyss the abyss also gazes into you." Friedrich Nietzsche

  7. #7

    Member Sales Rating: (0)

    Join Date
    Dec 2012
    Location
    Cleveland, Ohio
    Posts
    360

    Default

    Many big libraries have loudspeaker books by (1)David Weems or (2)Vance Dickerson. Both authors start slowly.

  8. #8

    Member Sales Rating: (2)

    Join Date
    Jun 2004
    Location
    New England
    Posts
    8,291

    Default

    Vance Dickason (that'll make his books easier to find) :-)
    http://www.parts-express.com/pe/show...number=500-035
    all the best,
    mrh

  9. #9

    Member Sales Rating: (0)

    Join Date
    Aug 2013
    Location
    TexSis
    Posts
    90

  10. #10

    Member Sales Rating: (0)

    Join Date
    Aug 2013
    Location
    TexSis
    Posts
    90
    Last edited by Polk&Beans; 12-05-2013 at 08:26 PM.

  11. #11

    Member Sales Rating: (0)

    Join Date
    Aug 2013
    Location
    TexSis
    Posts
    90

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts