Free Shipping on All Orders 1-866-764-1801

Vist our Online Store
+ Reply to Thread
Results 1 to 28 of 28
  1. #1

    Member Sales Rating: (0)

    Join Date
    Aug 2007
    Posts
    9

    Post Dual Polk Audio Sr124 enclosure recomendation?

    I have two SR124 subs and I had them in a 1.0 cu.ft. enclosure and they were loud even setting off my first car alarm but it wasn't enough. I want them to hit lower and harder. I am guessing I should go with a low tuned ported box. I checked the Sub box info section and it gives you basic dimensions but it doesn't tell me the tuning frequency, if it is a slot port or square, where to put the port. So if anyone has any suggestion that would be good.


    System:
    Pioneer 5900iB cd player w/ iPod hookup
    Jl Audio XR650 components
    Jl Audio XR650 rear coaxials
    JBL GTO 75.4 at 100rms x 4
    2 Polk Sr124 subs
    Rockford Fosgate t1500bd

  2. #2

    Member Sales Rating: (0)

    Join Date
    Dec 2003
    Location
    Chattanooga, TN
    Posts
    11,819

    Default

    A ported box wont hit as low as a sealed box, and it wont hit any harder. It may be louder in the upper end but thats it.

    If you want more impact than a pair of powerhouse 12's and 1500 watts can deliver, youre going to have to move up to an SPL sub, bu another SR12 or get a 2000 watt amp.
    polkaudio sound quality competitor since 2005
    MECA SQ Rookie of the Year 06 ~ MECA State Champ 06,07,08,11 ~ MECA World Finals 2nd place 06,07,08,09
    08 Car Audio Nationals 1st ~ 07 N Georgia Nationals 1st ~ 06 Carl Casper Nationals 1st ~ USACi 05 Southeast AutumnFest 1st

    polkaudio SR6500 --- polkaudio MM1040 x2 -- Pioneer P99 -- Rockford Fosgate P1000X5D

  3. #3

    Member Sales Rating: (0)

    Join Date
    Nov 2007
    Posts
    27

    Default

    Is that 1.0cft before displacement? If thats the case that enclosure is a little small. The minimum for a single sub is suppose to be .88cft after displacement. Personally, I'd stick with sealed and go with something between 1.34cft-1.20cft before displacement. The box I'm putting my 2 SR124-DVC subs in is about 2.4cft total so each sub will have about 1.2cft in its own chamber which after displacement would be 1.06cft. The box is 14x28x14 but of course I had to take into account thickness of the wood (.75") and subtracted that.

  4. #4
    Polk Customer Service
    Member Sales Rating: (0)

    Join Date
    Jul 2001
    Location
    Polk Audio
    Posts
    723

    Default

    If your goal is sound quality, then I would suggest installing each sub into a sealed enclosure volume that has a gross of 1.4 cubic feet. Driver displacement for this
    sub is .14 cubic feet. The net volume needs to be at least 1.2 cubic feet.
    This will result in a "QTC" of .707

    A box volume of 1.0 cubic feet, minus driver displacement, is really too small for these subs. (.86 net)
    It also restricts cone displacement "aka" excursion, and will produce a "harder" sounding bass. You also run the risk of damaging the voice coils when driving them hard due limiting the excursion of the smaller sealed enclosure volume.

  5. #5

    Member Sales Rating: (0)

    Join Date
    Sep 2007
    Location
    Huntington Beach, CA
    Posts
    70

    Default

    Quote Originally Posted by moreyb22 View Post
    I have two SR124 subs and I had them in a 1.0 cu.ft. enclosure and they were loud even setting off my first car alarm but it wasn't enough. I want them to hit lower and harder. I am guessing I should go with a low tuned ported box. I checked the Sub box info section and it gives you basic dimensions but it doesn't tell me the tuning frequency, if it is a slot port or square, where to put the port. So if anyone has any suggestion that would be good.


    System:
    Pioneer 5900iB cd player w/ iPod hookup
    Jl Audio XR650 components
    Jl Audio XR650 rear coaxials
    JBL GTO 75.4 at 100rms x 4
    2 Polk Sr124 subs
    Rockford Fosgate t1500bd

    I built a 3/4" MDF, Dual Sealed for my SR124 DVC's. I went with the 1.2 final volume for each side, (1.4 before displacement). Each is being pushed by a Polk 500 monoblock at 2 ohm each. I was not at all happy with how hard they hit. Maybe more power would have made a difference. I ended up having to go smaller on my enclosure and ended up with 1.06 final in order to get them to hit nearly as hard as my MM12 subs at 2 ohm on a single 500.1.

  6. #6

    Member Sales Rating: (0)

    Join Date
    Jan 2006
    Posts
    96

    Default

    To get what you want, you were correct in saying that you need a low tuned ported enclosure. I would say tune to 25-30 Hz and go with a volume of 2 cubid feet or larger. I'll throw the specs into Win ISD and see what I come up with for ya.

    EDIT:

    Enclosure info for ya:

    2 cubic feet NET volume
    4" vent 20" long (tunes to 27Hz)

    or

    2.5 cubic feet NET volume
    5" vent 20" long (tunes to 30HZ)

    Those are just two random box volumes, but they model up great. You are going to see increased low frequency output as well as more across the entire sub range. Keep in mind a subsonic filter is a must just set it to 20-25 Hz or so and you'll be good. I would personally go with the larger of the two.
    Last edited by GLN305; 12-08-2007 at 11:43 AM.

  7. #7

    Member Sales Rating: (0)

    Join Date
    Aug 2007
    Posts
    9

    Default

    I found a site that is building me a custom enclosure for them. I told what I wanted and gave them the specs and had the guy play around with it in the software. He came up with a 3.4 cu.ft. dual enclosure tuned to 30hz. I am still waiting for its completion but he is going to send me some pics as soon as its done so I will keep you posted.

  8. #8

    Member Sales Rating: (0)

    Join Date
    Oct 2007
    Location
    Mexico
    Posts
    400

    Default

    Quote Originally Posted by moreyb22 View Post
    I found a site that is building me a custom enclosure for them. I told what I wanted and gave them the specs and had the guy play around with it in the software. He came up with a 3.4 cu.ft. dual enclosure tuned to 30hz. I am still waiting for its completion but he is going to send me some pics as soon as its done so I will keep you posted.
    please keep us informed

    im actually thinking in buy the second Sub, but im not sure, i will have to listen the one i recently buy first.
    /////Alpine CDA-9887 HU
    /////Alpine KTX-1000EQ
    /////Alpine PDX-4.100
    /////Alpine PDX-1.1000
    Polk Audio SR 6500
    Polk Audio SR 124 DVC
    KnuKonceptz Kristal Kable

  9. #9

    Member Sales Rating: (0)

    Join Date
    Aug 2007
    Posts
    9

    Default

    The guy building my box sent me a pic of the unfinished box so I could make sure I liked it. It shipped out tuesday and I am expecting friday. So I am pretty excited. I hope to have it in sometime during my christmas break.

    Here is the pic:

  10. #10

    Member Sales Rating: (0)

    Join Date
    Dec 2006
    Location
    Canada
    Posts
    649

    Default

    Hope you enjoy it!

    btw, I think you're picture's link is broken, I don't see anything :(

  11. #11

    Member Sales Rating: (0)

    Join Date
    Aug 2007
    Posts
    9

    Default Having a little problem need help.

    I have to say Mac and everyone you were right the ported was not any better. I decided to go back to my sealed box. The only problem is that before I blew both of my subs about a month or two in. I had them in a 1 cu.ft. box before displacement and someone had previously mentioned this might be to small. Could this be the reason for them blowing. I did noticed when I first got them that after a couple of hours of listening they would get really hot. Should I get a 1.2 cu.ft box because I noticed on the website it says a 1.2 give competition quality.
    Last edited by moreyb22; 01-10-2008 at 10:26 PM.

  12. #12

    Member Sales Rating: (0)

    Join Date
    Oct 2007
    Location
    Mexico
    Posts
    400

    Default

    Quote Originally Posted by moreyb22 View Post
    I have to say Mac and everyone you were right the ported was not any better. I decided to go back to my sealed box. The only problem is that before I blew both of my subs about a month or two in. I had them in a 1 cu.ft. box before displacement and someone had previously mentioned this might be to small. Could this be the reason for them blowing. I did noticed when I first got them that after a couple of hours of listening they would get really hot. Should I get a 1.2 cu.ft box because I noticed on the website it says a 1.2 give competition quality.
    check this:

    http://www.polkaudio.com/downloads/w...WhitePaper.pdf

    On page 13 on the PDF (or 12 on the document)

    the problem is that the website says one displacement, and then the white paper says another.

    but its suppossed to be 1.3 or 1.4 for the best sound

    for example i have the 1.4 Net, (1.56 without displacement)

    And always remember to leave 2" or more of space between the rear end of the driver, and the backside of the enclosure for clearance, and to avoid over heating.
    /////Alpine CDA-9887 HU
    /////Alpine KTX-1000EQ
    /////Alpine PDX-4.100
    /////Alpine PDX-1.1000
    Polk Audio SR 6500
    Polk Audio SR 124 DVC
    KnuKonceptz Kristal Kable

  13. #13

    Member Sales Rating: (0)

    Join Date
    May 2008
    Posts
    19

    Default

    i just put my sr124 sub in a ported box and it sounds way better than sealed. I guess it all depends on the car. Funny how everyones opinions of bass sounding good differs

  14. #14

    Member Sales Rating: (0)

    Join Date
    Jun 2007
    Location
    Laker City (LA), CA
    Posts
    1,060

    Default

    well... its a sound quality forum..... POLK is sound quality not SPL. ported is known to be more SPL. thats why when u read these forums just about everyone is gonna say go sealed.
    2013 Toyota Prius - Planning this one out.

  15. #15

    Member Sales Rating: (0)

    Join Date
    May 2006
    Posts
    45

    Default

    Hello,
    I just purchased two SR124-DVC, and while I was thinking what kind of enclosure to use, this thread attracted my attention.

    See, my main concern is SQ, but I'm willing to sacrifice some SQ for more SPL, only and only if the SPL gain is more than the loss in SQ. As you can see, I'm trying to find the optimal SQ&SPL combination.

    So, I have seen many enclosure recommendations in this thread, but none seems to point to the best one for SQ. I see sealed recommendations totaling a range between 1 cu. ft. and 1.5 cu. ft. net of displacements, but no final conclusion was achieved regarding the best SQ enclosure internal volume. So this forces me to ask: what is finally the best internal volume net of displacement to use so as to achieve the best SQ setup?

    Now, the optimality subject points me to the next question. Once the best SQ setup is defined, we must see if moving to a ported box actually adds total value: with this I mean, if it augments the total SQ&SPL value, maybe by sacrificing some SQ, but the SPL gain would be greater than the loss in SQ. So, the next question is: Is there any ported box setup such that the SPL gain more than offsets the loss in SQ? If so, which would it be?

    Sorry it it's too large a post, but needed to do so since I really want to get the best from my new polks!

  16. #16

    Member Sales Rating: (0)

    Join Date
    Sep 2008
    Location
    pa
    Posts
    459

    Default

    spl gains don't offset sq losses, least not for me. what vehicle this going in? optimality speaking, over 1200wrms(at least, and 2400w of dynamic power{at least]) going into 2 12" SRs...how much more SPL u need? none if your serious about SQ. hell, all u really need is 1, specially with that amp(PA1200). i wouldn't even think about going ported...
    Polk MM6501 kick panels, Eclipse cd7200mkll and SW9122 Bomb Box, Cadence A4, A7, CAP5, JL8W3V3

  17. #17

    Member Sales Rating: (0)

    Join Date
    May 2006
    Posts
    45

    Default

    This system is going into a 2007 Jeep Liberty. I want sound quality, but it's not irrational to lose some SQ only if the gain in SPL is much more. I'm serious about SQ, but there could be times that I would want to explode some techno in open beach with friends, so it makes sense to change enclosure only if the gain in SPL offsets the lose in SQ.

  18. #18

    Member Sales Rating: (0)

    Join Date
    Sep 2008
    Location
    pa
    Posts
    459

    Default

    ok. yeah it would make sense if u were talkin 2 sony explodes or 1 SR running off a HU. but 2 SRs, talking at least 1200wrms, technos gonna b exploding any beach ur at. preference comes to play but...i think u may b happier with 1 SR, ported.. get a bomb box bitch!(not refering to u, push, rhetorically speaking..get a bomb box bitch!)
    and if u do go dual ported SRs, pa1200 is more than enough. sealed, could def go w/ more..

  19. #19

    Member Sales Rating: (0)

    Join Date
    May 2006
    Posts
    45

    Default

    I'm not sure why you said I would be happier with 1 SR124-DVD in a ported box, and don't know what you meant by "box bomb bitch", but thanks for your advices, though I still don't know what to conclude from them.

    I still got doubts about what internal volume should I use for the sealed enclosure. The manual says 0.88 cu. ft. and 0.14 cu. ft. for displacement, giving a total of 1.02 cu. ft. But this thread has mentioned many different internal volume numbers, mostly greater than what the manual explains, saying that maybe more volume can reach better SQ levels. So I'm too confused: what is finally the optimal internal volume gross of woofer displacement to be used in a sealed enclosure with a Polk SR124-DVC?

  20. #20

    Member Sales Rating: (0)

    Join Date
    Sep 2008
    Location
    pa
    Posts
    459

    Default

    wellll u want sq hence same sub setup as sq champ macleod (1 sr12) but u want people in china 2 hear it (ported). didn't say box bomb, bitch, said "bomb box" bitch check it out think its perfect volume for SR also..

  21. #21

    Member Sales Rating: (0)

    Join Date
    May 2006
    Posts
    45

    Default

    I don't know what's that "bomb box bitch", but really, I just got the two SR124-DVC here and I still don't know on what enclosure to put them into.

    Please, someone, help me find the best internal volume gross of woofer displacement, for a sealed enclosure, such that the SQ is optimal.

    Thanks.

  22. #22

    Member Sales Rating: (0)

    Join Date
    Oct 2007
    Location
    Mexico
    Posts
    400

    Default

    I have 1.25 cubic feet without the driver inside, its just for one driver..

    you can do 2 separate enclosures, and then put them together..
    Last edited by Kinetic; 08-11-2009 at 10:53 PM.
    /////Alpine CDA-9887 HU
    /////Alpine KTX-1000EQ
    /////Alpine PDX-4.100
    /////Alpine PDX-1.1000
    Polk Audio SR 6500
    Polk Audio SR 124 DVC
    KnuKonceptz Kristal Kable

  23. #23

    Member Sales Rating: (0)

    Join Date
    Oct 2007
    Location
    Mexico
    Posts
    400

    Default

    sounds hard in volume and low in frecuencies, I use to have it bigger enclosure, but this is the best one, and if you put a smaller one you can burn your sub..

    check the white paper.. you have a minimum and a maximum
    /////Alpine CDA-9887 HU
    /////Alpine KTX-1000EQ
    /////Alpine PDX-4.100
    /////Alpine PDX-1.1000
    Polk Audio SR 6500
    Polk Audio SR 124 DVC
    KnuKonceptz Kristal Kable

  24. #24

    Member Sales Rating: (0)

    Join Date
    May 2006
    Posts
    45

    Default

    Thanks Kinetic. Checking again its white paper, I figured out that the smaller the box the punchier the sound, while the larger the box the deeper the bass. This will be left then to ones personal preferences.

    However, further ahead in the same page of the white paper, it says "If you are looking for the ultimate in loudness .... a ported enclosure may be the way to go." But it does not specify its required internal volume nor the port specs. Where can I find such official and optimal ported enclosure specs and comparisons in SQ vs. the sealed enclosure?

  25. #25

    Member Sales Rating: (0)

    Join Date
    Oct 2007
    Location
    Mexico
    Posts
    400

    Default

    the sealed its the way to go for this sub
    /////Alpine CDA-9887 HU
    /////Alpine KTX-1000EQ
    /////Alpine PDX-4.100
    /////Alpine PDX-1.1000
    Polk Audio SR 6500
    Polk Audio SR 124 DVC
    KnuKonceptz Kristal Kable

  26. #26

    Member Sales Rating: (0)

    Join Date
    May 2006
    Posts
    45

    Default

    Thinking about this subject cautiously, I decided to better go sealed; this subs were optimized for a sealed environment and not for ported. I would then choose the middle of the recommended range for internal volume to strike a balance between "punchness" and deepness.

    Thanks to all who helped me here.

  27. #27

    Member Sales Rating: (0)

    Join Date
    May 2006
    Posts
    45

    Default

    Quote Originally Posted by Kim View Post
    If your goal is sound quality, then I would suggest installing each sub into a sealed enclosure volume that has a gross of 1.4 cubic feet. Driver displacement for this
    sub is .14 cubic feet. The net volume needs to be at least 1.2 cubic feet.
    This will result in a "QTC" of .707

    A box volume of 1.0 cubic feet, minus driver displacement, is really too small for these subs. (.86 net)
    It also restricts cone displacement "aka" excursion, and will produce a "harder" sounding bass. You also run the risk of damaging the voice coils when driving them hard due limiting the excursion of the smaller sealed enclosure volume.
    Do I take into account the driver displacement simply by adding up 0.14 cu. ft. to the total enclosure volume? That's all? No internal additional manipulation needed nor anything special at all?

  28. #28

    Member Sales Rating: (0)

    Join Date
    May 2006
    Posts
    45

    Default

    ^^^ No insights onto that?

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Similar Threads

  1. SR124-DVC Enclosure
    By Remyngton in forum Car Subwoofer Talk
    Replies: 58
    Last Post: 01-15-2008, 07:16 PM
  2. Sr124-dvc possibly in a wrong enclosure.
    By csnut18 in forum Car Audio & Electronics
    Replies: 17
    Last Post: 08-14-2007, 10:48 PM
  3. Some questions about enclosure for SR124
    By monologuist in forum Car Audio & Electronics
    Replies: 10
    Last Post: 07-07-2007, 01:42 AM
  4. SR124 Amp and Enclosure
    By mamomark in forum Car Audio & Electronics
    Replies: 5
    Last Post: 05-20-2007, 11:57 PM
  5. Polk SR124-DVC vs JL Audio W6v2
    By DAlba in forum Car Audio & Electronics
    Replies: 27
    Last Post: 03-18-2006, 10:39 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts