Free Shipping on All Orders 1-866-764-1801

Vist our Online Store
+ Reply to Thread
Results 1 to 2 of 2
  1. #1

    Member Sales Rating: (0)

    Join Date
    Sep 2007
    Location
    gate city virgina
    Posts
    217

    Exclamation subwoofer wiring help

    I have a fusion EN-AM8001 Encounter Monoblock Amplifier, the spec are as follows:
    Product Specifications

    262 Watts RMS x 1 Channel @ 4 Ohms and 1% THD+N
    368 Watts RMS x 1 Channel @ 2 Ohms and 1% THD+N

    Max Power Rating: 800 Watts
    THD @ Rated Power 1kHz/100Hz: 0.1%
    Frequency Response Hz (-3dB): 10Hz - 250Hz
    Signal to Noise: >90
    Variable Low Pass Filter: 6dB/Octave
    Bass Boost @ 45Hz: 0dB/6dB/12dB
    Input Sensitivity: 0.2-8V
    Input Impedance: 20K
    Fuse Rating: 25A x 2

    It is a 2ohm stable amp, my guestion is how do i wire my sub to be 2ohm stable?
    The specs for the sub are as follows:

    It is a Volfenhag zx-4712 1000w max 4ohm + 4ohm dual voice coil usable impedence is 2-8 ohm. How do i wire this thing at 2 ohm stable?

    If i can wire my sub 2 ohm stable ill get more rms out of my amp

    tyler
    __________________
    tyler birch

    ht system
    denon avr-1907
    polk audio monitor 70 towers
    nakamichi bx -100 tape deck
    sony 5 disc cd/dvd player hdmi ready
    velodyne dps-12 subwoofer
    tyler birch

    ht system
    denon avr-1907
    monitor 70 towers-polkaudio
    nakamichi bx -100 tape deck
    sony 5 disc cd/dvd player hdmi ready
    velodyne dps-12 subwoofer

    Car audio

    AMP: FUSION EN-AM8001 800 watts max 368 watts rms x 1 channel @ 2 ohms stable
    SUB: 12 INCH 1000W DVC VOLFENHAG 2 Ohm stable useable ohms 2-8ohms

  2. #2

    Member Sales Rating: (4)

    Join Date
    Dec 2002
    Location
    Denial...it's in Egypt.
    Posts
    12,882

    Default

    Here:

    http://www.termpro.com/articles/spkrz.html

    Read and learn.

    Speakers in Parallel

    Parallel wiring has the opposite effect of series wiring load impedance drops when speakers are wired in this fashion. And the more speakers you wire in, the lower the impedance. The most common reason for wanting to lower impedance is to raise acoustical output. Speaker output increases because the amplifier's power output rises as the load impedance decreases.

    The number of speakers that can be connected in parallel is limited by the minimum load impedance that the amplifier is capable of driving and the power-handling capacity of the speakers. In most cases, load impedance should be held to a minimum of 2 ohms provided the amplifier can handle impedances that low.

    Figure 2A shows how to wire a pair of speakers in parallel. A wire from the positive terminal of one channel of the amp is wired to the positive terminals on speakers A and B. (The simplest way to do this is to run a wire from the amp terminal to Speaker A and then run a second wire from that terminal to Speaker B.) Then the negative terminal of the same amp channel is wired in like fashion to the negative terminals on both speakers. The second channel is wired the same way.



    Calculating the load impedance for the parallel-wired channel in Figure 2A is a bit more complicated than doing so for speakers wired in series. Using Equation 4, multiply the impedances of each speaker and then divide the result by the sum of the speakers' impedances. You can visualize the result as a single imaginary speaker (Figure 2B), whose impedance is represented by Zt. Zt stands for the equivalent-load impedance, while Za and Zb represent the impedances of speakers A and B, respectively.

    Equation 4: Speakers in Parallel
    Zt = (Za x Zb) / (Za + Zb)

    Turning again to our subwoofer install, say you want even more oomph from your system. So you trade in the original amp for one that has the same 4-ohm power rating (100 watts x 2) but is also 2-ohm stable. Since the power output of most amps increases as impedance decreases, you could boost the amp's power output and the system's bass response simply by switching to a parallel wiring scheme. Doing so would drop the net, or equivalent-load, impedance for each channel to 2 ohms. Mathematically, you substitute 4 for Za and Zb in Equation 4 and work it through:

    Zt = (Za x Zb) / (Za + Zb)
    Zt = (4 x 4) / (4 + 4)
    Zt = 16 / 8
    Zt = 2 ohms

    To calculate the new amplifier's power output into 2 ohms, refer to Equation 2. Plugging in the appropriate numbers, the calculation goes as follows:

    Po = 100 x (4 / 2)
    Po = 100 x 2
    Po = 200 watts

    As you can see, by upgrading to a 2-ohm-stable amplifier and wiring the same four 15-inch woofers in parallel two per channel power output jumps fourfold from 50 watts x 2 to 200 watts x 2.

    Now, to find out how much power each subwoofer will receive when wired in parallel, we must use Equation 5, which is actually a scrambled version of Equation 3 (remember, we'll be working the equation for just one speaker (Pa)):

    Equation 5: Power Applied to Each Speaker
    Pa = Po x (Zt / Zn)

    Substituting 200 for Po, 2 for Zt, and 4 for Zn, the equation works through as follows:

    Pa = 200 x (2 / 4)
    Pa = 200 x 0.5
    Pa = 100 watts

    Since both subwoofers are rated at 4 ohms, the second one (Pb) would also receive 100 watts.
    That's what you need to do.

    For those who are impatient, Google is your friend. Took me all of 3 minutes to find and post it.
    You're just jealous 'cause the voices don't talk to you!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Similar Threads

  1. subwoofer wiring help
    By thumpin07 in forum Subwoofer Hookup & Bass Management
    Replies: 5
    Last Post: 05-02-2008, 10:53 AM
  2. subwoofer wiring
    By jizzo in forum Subwoofer Hookup & Bass Management
    Replies: 3
    Last Post: 01-27-2008, 06:49 PM
  3. Anyone try Bi-Wiring a Subwoofer
    By schwarcw in forum Subwoofer Hookup & Bass Management
    Replies: 10
    Last Post: 09-27-2005, 10:51 PM
  4. Subwoofer and wiring
    By probinator in forum Car Subwoofer Talk
    Replies: 4
    Last Post: 03-02-2004, 02:46 PM
  5. Subwoofer Wiring
    By brianc222 in forum Basic Hookup/Wiring Questions
    Replies: 7
    Last Post: 06-04-2003, 08:14 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts