Please Help!!

[dmhaenke]

i just got a 4 channel 1800 watt crunch p1800.4 amp and i have to 800 watt Pioneer subs now i know not to have the gain up all the way and stuff so i dont blow the subs but im not sure how to wire it if i just wire it normal (conect one to channel one and one to channel 2) or if i need to bridge it witch im not quite sure how to do that really i could really use some help i have about 3 days till i install and i wanna do it right. im not to new to wiring amps and subs just to 4 channel ones.......Please help

[cadenceclipse]

r they dvc or svc?

[dmhaenke]

they are four-layer with aluminum bobbin the subs are Pioneer 12" Subwoofer, TS-W302R

[dmhaenke]

* Cone material: injection-molded polypropylene (IMPP) composite for strength and durability
* Surround: urethane, dual layer
* Magnet type: strontium
* Voice coil: four-layer with aluminum bobbin
* Damper: Conex for linear bass response<
* Basket design: stamped with magnet cover
* Gasket: molded
* Terminals: spring compression
* Nominal power handling capability: 150 watts RMS
* Maximum music power handling capability: 800 watts
* Frequency response: 20 to 4000 Hz
* Sensitivity: 91 dB (1 watt at 1 meter)
* Impedance rating: 4 ohms
* Mounting depth: 5.75 inches
* Cut-out dimension: 10.9 inches
* Weight: 1.5 lbs.
* Recommended enclosure size: 1 to 2 cubic feet


there are the stats

[cadenceclipse]

usualy 2 subs on one 4 channel u would bridge 2 channels to each sub. your gonna hook 1 sub to ch1 (+) and ch 2 (-). other sub ch 3(+) and ch. 4 (-). what is amps power rating (rms)?(important, if amp puts out 1800w, which it doesn't, you might blow them subs . but would still like to know rms power per channel and bridged(4ohm)

[dmhaenke]

1800W 2 / 3 / 4-Channel A/B Class Amplifier
225W x 4-Ch @ 4-Ohms or
450W x 4-Ch @ 2-Ohms or
900W x 2-Ch @ 4-Ohms Dynamic Music Watts
SEPP A/B-Class P-Series Amplifier Designs
Bridgeable Designs: All 2-Ch & 4-Ch
Illuminated, Large New Design Crunch Logo
P. MOSFET Pulse Wave Modulated Power Supply For Instant Maxx Current Output
1-Ohm Capable A/B Class Mono Block Amps
2-Ohm Capable A/B Class 2/4/5-Ch Amps
4-Ch Amps Config to 3-Ch R & L and Sub Mode
Rugged MOSFET Audio Outputs
P-Series Amp Protection with System Diagnostics LED's That Protects Against:
Current / Amperage Overload
Short Circuits
Thermal Overload
DC Offset
2/4Ch Amps Have Hi-Level Speaker Lead Inputs
Silver Preamp Level RCA Inputs
Daisy Chain Line Outputs (except P-Series 5000.5)
Mono Blocks & 5-Channel P-Series Amp Include a Remote Bass Control
Versa Cross™ Sound Shaping Controls *
Mono/Stereo Switch
HP/LP/Full-Pass Freq. Selections
Crossover Frequency Adjustments:
(60 Hz to 1.2kHz for all multi-Ch amps)
(30 Hz to 250 Hz Low-Pass *)
*Exception: P 1000.1 & P 1500.1 are Low-Pass Only
Adjustable (60Hz to 150Hz) & Include Variable Subsonic
Filter (15Hz to 55Hz)
4-Ch P-Series Include Separate F & R Bass EQ Controls Adjustable +12dB Bass EQ @ 45Hz
Input Level Control (0.2 to 5V for all 2/4/5-Ch Amps or 6V for P Mono-Block Amps)
Oversized Speaker Terminals
Powered By Maxxsonics" Technology

[cadenceclipse]

sounds like pretty serious 4 shannel. owners manual should say, but using wiring mentioned above they would c 900 each but since SVC, only 450 each, which sounds fine, just watch gains

[dmhaenke]

and what about a Capacitor? should i get one and if so what size?

[cadenceclipse]

stock electrical system? if so u could use more like an upgraded alternator or extra battery at least. cap won't hurt, guess they say 1 farad per 1000w, i use 5 farad on 1100w