Amps
PA D5000.5
Super efficient class D bridgable 5-channel mobile audio amplifier
1 13/16" H x 13 5/16" W x 6 3/4" D
4.60cm H x 33.81cm W x 17.14cm D
$44995each
PA D5000.5
The PA D5000.5 is our big gun 5-channel beast that enables you to drive all your speakers and a subwoofer and never break a sweat. A toroidal transformer helps keep the PA D5000.5 neatly packaged in a sleek aluminum extruded design under 2-inch tall while it pumps out gobs of clean, efficient power. A low THD, a high signal-to-noise ratio, plus wide bandwidth frequencies, make the PA D5000.5 uncompromising performance in your any vehicle's sound system.
Sleek, Compact, Powerful
The PA D5000.5 is capable of bridging two full-range channels into a single full-range channel with higher output power. For instance, the front channels (FL and FR) when wired correctly will increase the output power from 70W per channel to 200W per channel (for a 4 ohm load). The same can be done for the rear channels (RL and RR). The most common configurations are four full-range channels and a subwoofer channel, or two bridged full-range channels and a subwoofer channel.
PA D5000.5 Features:
Super-efficient class D design—Runs much cooler than conventional amps.
High-speed MOSFET switching—Power supply with outputs stable into 2 ohm loads for full range channel speakers and 1 ohm loads for subwoofer channel.
Protection—Thermal, DC offset, reverse DC voltage and short circuit protection.
Sub 1/Sub 2 Inputs—Line level inputs for subwoofer signal from head unit
SUB/INT source switch—In the INT position, the amplifier will filter the bass frequencies from the full range signal and send them to the subwoofer amplifier channel.
SUB sonic filter—Attenuates the frequencies below the settings on the control.
Remote bass level control—Set gain to match output from head unit.
Rear Full, HPF switch—Selects between no filtering or a high pass filter to dial in your speakers’ blending.
Channel mode switch (4CH/ST)—In the ST position, the amplifier sends the same signal to the front and rear channels.
Nickel-plated wire terminals & RCA connectors—Ensure maximum signal transfer.
Stainless steel hardware—Used throughout won’t corrode in humid environments.
Electrical | |
|---|---|
| Total Frequency Response | 20Hz-20kHz |
| Signal-to-noise (Referenced to rated power) | 105 dBA |
| Remote Gain | yes, for bass |
| Distortion at Rated Power | <0.1 % |
| Minimum Impedance Bridged | 4 ohms |
| Minimum Impedance Not Bridged | 2 ohms |
| Protection Circuitry | Thermal, DC offset, reverse DC voltage and short circuit; fuses: two 40 Amp ATC |
| Subsonic Filter | yes |
| High Pass Filter | |
| Filter Slope | 12dB/octave |
| Filter Frequency | 40Hz-400Hz(front)/40Hz-4kHz(rear) |
| Low Pass Filter | |
| Filter Frequency | 80Hz-4kHz(front) |
| Max Sensitivity | 200mV-6V dB |
Dimensions | |
|---|---|
| Cabinet Dimensions | |
| Height | 1 13/16" (4.60cm) |
| Width | 13 5/16" (33.81cm) |
| Depth | 6 3/4" (17.14cm) |
| Product Weight (each) | 6.750 lbs. pounds |
| With Panels | |
| Height | 1 13/16" (4.60cm) |
| Width | 13 5/16" (33.81cm) |
| Depth | 6 3/4" (17.14cm) |
Amplifier Specs | |
|---|---|
| Power Specs | 100W x 4, 400W x 1 RMS @ 2 ohms; 70W x 4, 200W x 1 RMS @ 4 ohms; 200W x 2 RMS bridged @ 4 ohms; 500W x 1 RMS @ 1 ohm (sub) |
| Channels | 5 |
| Channel Notes | Bridgeable Class D MOSFET |
| 12V & Ground Cable Gauge | 4AWG |
Amplifier Power Specs | |
|---|---|
| RMS Power at 14.4V | |
| Watts per channel NOT bridged @ 1 kHz | |
| 4 ohms | 70 x 4 watts |
| 2 ohms | 100 x 4 watts |
| Watts per channel bridged | |
| 4 ohms | 200 x 2 watts |
Specifications, dimensions and features subject to change without notice. For more information call us at 1-800-377-7655 (USA and Canada). Outside of North America call +1 (410) 358-3600.
Customer Reviews
1 reviews with an average of 5
Write your own reviewby Brian B., February 1, 2012
25 out of 25 people found this review helpful.Strengths:
New D series amps are smaller in design yet still deliver huge power.
Weaknesses:
none really, but I should mention the wierd design for power/ground/remote inputs. The power, ground and remote wire adapter that comes with the amp has a small hole for the typical 18 gauge remote wire but larger holes (0 gauge) for the power/ground. The stock amp holes for the power and ground are designed for a 4 gauge or smaller cable, however the remote wire hole is for a 10 gauge cable so you are forced to use the adapter that bumps the power/ground wire size up to a 0 gauge wire. Everything hooked up fine just the 4 gauge cable was small for the hole. I think they did this so the adapter would slide right into the holes...not for sure though. If you are mounting the amp at a 90 degree on a board behind the seat, the screws are a pain to get in unless you are using a magnetic screw driver or tape the screw to the screw driver. These do not hurt the overall quality of the amp just a few frustrations I came across when installing it.
Review:
Amp is doing great so far! I have it pushing four Polk DXI6500 component speakers in my crew cab Chevrolet Silverado and one Kicker 2ohm 10" sub rated at 400 watts rms. Amp is no where near maxed out and the system sounds great! There is no road noise in the system and it is paired with a Pioneer AVH-P4300DVD HU.
PA D5000.5 Media
PA D5000.5 Literature
Want to know more? Want to dig just a little deeper to learn about this product? Here's a list of source material that will give more detail, other perspectives, and answer questions you may have.